Войти:
Оценок - 2, средний балл: 5 ( )

Инструкция по эксплуатации Asus, модель AP1720-E2

Производитель: Asus
Размер: 3.92 mb
Название файла: e1733_ap1720-e2.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Configuration options: [Disabled] [201] [209] MIDI Port IRQ [10] Allows you to select the MIDI port IRQ. Configuration options: [Disabled] [5] [10] ASUS AP1720-E2 barebone server SATA Configuration SATA Configuration *** On-Chip Serial ATA Setting *** On-Chip Serial ATA [Auto] SATA Mode IDE Serial ATA Port0 Mode SATA0 master Serial ATA Port1 Mode SATA1 master **On-Chip Serial ATA Setting Select Menu Item Specific Help [Disabled]: Disable SATA Controller. [Auto]: Auto-arrange the BIOS. [Combined Mode]: PATA and SATA are combined. Max. of 2 IDE drives on each channel. [Enhanced Mode]: Enable both SATA and PATA. Max. of 6 IDE drives are supported. [SATA Only]: SATA is opeating in legacy mode. The items SATA Mode, Serial ATA Port0 Mode, and Serial ATA Port1 Mode are not configurable when the On-Chip Serial ATA item is set to [Disabled]. On-chip Serial ATA [Auto] This item allows you to configure your serial ATA devices if present. Configuration options: [Disabled] [Auto] [Combined Mode] [Enhanced Mode] [SATA Only] Setting the On-chip Serial ATA item to [Auto] or [Enhanced Mode] enables the items Third IDE Master and Fourth IDE Master in the Main menu. See page 4-14 for more information. a. Setting to [Auto] allows BIOS to automatically configure the SATA devices. b. Setting to [Combined Mode] allows you to install parallel ATA and serial ATA devices at the same time. You may install two IDE devices on any of the parallel ATA channels, and one IDE device on each serial ATA channel for a maximum of four devices. c. Setting to [Enhanced Mode] allows you to install Parallel ATA and Serial ATA devices at the same time, with a maximum of six IDE devices on each channel. Chapter 5: BIOS setup 1. Use the [Enhanced Mode] option if you installed a native operating system like Winows 2000/XP. 2. You may not use this option if you are using Linux RedHat 8 or 9 version operating system, as they do not support native mode. d. Setting to [SATA Only] allows you to install IDE devices on the Serial ATA channels only. e. Setting to [Disabled] disables the onboard SATA controller. The RAID feature is also disabled. SATA Mode [IDE] When this item is set to [IDE], SATA operates in IDE mode. When set to [RAID], SATA operates in RAID mode. The RAID feature allows configuration of the installed IDE devices into a disk array. Configuration options: [IDE] [RAID] Serial ATA Port0 Mode [SATA0 Master] Serial ATA Port1 Mode [SATA1 Master] Allow you to set the SATA Port0 and Serial ATA Port1 modes. The options for these items vary depending on the setting of the On-Chip Serial ATA item. Configuration options: [Primary Master] [Primary Slave] [Secondary Master] [Secondary Slave] [SATA0 Master] [SATA1 Master] ASUS AP1720-E2 barebone server 5.4.6 PCIPnP This menu shows the PCIPnP configuration settings. Select an item then press to display a pop-up menu with the configuration options. PCIPnP Reset Configuration Data Resources Controlled By IRQ Resources PCI/VGA Pallete Snoop INT Pin 1 Assignment INT Pin 2 Assignment INT Pin 3 Assignment INT Pin 4 Assignment INT Pin 5 Assignment INT Pin 6 Assignment INT Pin 7 Assignment INT Pin 8 Assignment [Disabled] [Auto] [Disabled] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] Select Menu Item Specific Help Default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) upon exiting Setup, if you installed a new add-on card and the system cannot boot due to a serious conflict in system configuration. Reset Configuration Data [Disabled] Allows you to enable or disabled resetting of the Extended System Configuration Data (ESCD) when you exit the Setup. The ESCD includes information on non-PnP devices. Set this item to [Enabled] if you installed an expansion card that conflicts with other devices and cause system boot failure. Configuration options: [Disabled] [Enabled] Resources Controlled By [Auto] When set to [Auto], allows BIOS to automatically configure of all boot and Plug and Play devices. When set to [Manual], you can assign the available IRQ Resources to the PCI devices. Configuration options: [Auto] [Manual] When the item Resources Controlled By is set to [Auto], the item IRQ Resources is grayed out and not user-configurable. Refer to the section “IRQ Resources” for information on how to enable this item. PCI/VGA Pallete Snoop [Disabled] Some non-standard VGA cards, like graphics accelerators or MPEG video cards, may not show colors properly. Setting this field to [Enabled] corrects this problem. If you are using a standard VGA card, leave this field to the default setting [Disabled]. Configuration options: [Disabled] [Enabled] Chapter 5: BIOS setup INT Pin 1~8 Assignment [Auto] Allows you to select the appropriate interrupt to the specific devices to avoid conflict. Configuration options: [Auto] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15] IRQ Resources Set the item Resources Controlled By to [Manual] to enable the item IRQ Resources and assign the interrupts ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории