|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
HP ProLiant DL170h G6
Overview
2. Install the bottom piece of the graphics card support bracket.
Figure 4 Installing the top piece of the graphics card support bracket
o
Align the bottom piece of the graphics card support bracket
Graphics Card
This document contains instructions for installing graphics card
to the chassis. (step 1 in Figure 2)
support bracket and the power cable into HP ProLiant DL170h G6
o
Fasten the screw to secure the bracket to the chassis. (step
servers.
Bracket/Cable Kit
2 in Figure 2)
NOTE: For more information on preparing the server for
o
Open the latch at the rear panel and remove blank. (step 3
installation, refer to the HP ProLiant DL100 Series Server
in Figure 2)
Installation Instructions
User Guide included in the Easy Set-up CD.
Kit Contents
Figure 2 Installing the bottom piece of the graphics card support
bracket
•
Graphics card support bracket
•
Power cable
•
Installation instructions
Important Safety Information
Refer to the Important Safety Information document included with the
5. Install the power cable.
server.
o
Install the 12 pin power cable connector to the power cable
on the power backplane. (step 1 in Figure 5)
WARNING: Electrostatic discharge (ESD) can damage
electronic components. Be sure you are properly
o
Install the 8 pin power cable to the 8 pin power connector
grounded (earthed) before beginning any installation
on the graphics card. (step 2 in Figure 5)
procedure.
Figure 5 Installing the power cable
Installation Guidelines
3. Install the graphics card.
This installation is to be performed by qualified individuals who are
knowledgeable of the procedures, precautions, and hazards
o
Align and put the graphics card into the chassis, making
associated with equipment containing hazardous electrical circuits.
sure it is secured by the slot on the air duct and the edge of
the riser card. (step 4 in Figure 3)
Installing the graphics card support
Figure 3 Installing the graphics card
bracket and power cable
1. Remove the PCI Holder.
o
Press the hooks and remove the PCI holder from the Riser
Air Baffle.(step 1 and 2 in Figure 1)
Figure 1 Removing PCI Holder
Legal notices
6. Reinstall the top cover.
© Copyright 2009 Hewlett-Packard Development Company, L.P.
7. Reinstall unit into rack.
8. Connect all external cables and the AC power cord to the
The information contained herein is subject to change without notice. The
system.
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
9. Press the power button on the front panel to turn on the server.
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
4. Install the top piece of the graphics card support bracket.
o
Close the latch at the rear panel. (step 5 in Figure 4)
o
Fasten the screws to secure the graphics card to the chassis.
(step 6 in Figure 4)
o
Align the top piece of the graphics card support bracket to
the screw holes and spools on the bottom piece of the
graphics card support bracket. (step 7 in Figure 4)
NOTE: Please retain the PCI Holder for future use with
other cards.
o
Fasten the screw to secure the top piece of the graphics
card support bracket. (step 8 in Figure 4)
Part number 538638-002
September 2009 (second edition)
...Эта инструкция также подходит к моделям:
Компьютеры - HP ProLiant DL4x170h G6 Server (799.9 kb)
Компьютеры - HP ProLiant DL170h G6 Server (799.9 kb)
Компьютеры - HP ProLiant DL80 Server (799.9 kb)