Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Security
System IDs
(Non-CTRL-A mode: Read-only, CTRL-A mode:
Resetting the password jumper
Read-write)
1. Shut down the operating system properly, then turn off the computer and any external
Product Name/Serial Number/UUID/SKU
devices, and disconnect the power cord from the power outlet.
Number/Family Name
2. With the power cord disconnected, press the power button again to drain the system
Asset Tag
of any residual power.
(This item will be shown when FBYTE support.)
3. Remove the access panel.
Feature Byte/Build ID
4. Locate the header and jumper.
5. On systems with 3-pin jumpers, remove the jumper from pins 1 and 2. Place the
Keyboard
jumper on pins 2 and 3. On systems with 2-pin jumpers, remove the jumper from pins
System Security
Data Execution Prevention
1 and 2.
Virtualization Technology
6. Replace the access panel.
Power
Hardware
SATA Power Management
7. Reconnect the external equipment.
Power
8. Plug in and turn on power. Allow the operating system to start. This clears the current
Management
S5 Maximum Power Savings
passwords and disables the password features.
S5 Wake on LAN
9. To establish new passwords, repeat steps 1 - 4, replace the password jumper on pins
Thermal
CPU Fan Speed
1 and 2, then repeat steps 6 - 8. Establish new passwords in Computer Setup.
CPU Fan Check
(accessible via
Clearing and Resetting the CMOS
Advanced Power-On
POST Messages
To provide a jumper to trigger reloading of all BIOS Setup default values. Once the
Options
jumper is detected as connected or activated, the BIOS will reset all modifiable BIOS
After Power Loss
Setup fields to their default values except for the system date, system time, Setup
POST Delay (in seconds)
password and Power-On password fields. In addition, display the following message:
BIOS Power-On Sunday/Monday/Tuesday/Wednesday
"Default BIOS settings have been loaded."
/Thursday/Friday/Saturday
1. Turn off the computer and any external devices, and disconnect the power cord from
Time (hh:mm)
The power outlet.
Bus Options
2. Disconnect the keyboard, monitor, and any other external equipment connected to the
PCI SERR# Generation
computer.
PCI VGA Palette Snooping
3. Remove the access panel.
Device Options
Num Lock State at Power-On
4. Locate the header and jumper.
NIC PXE Option ROM Download
CAUTION: Make sure you have disconnected the AC power cord from the wall
outlet. Clearing the CMOS while power is connected can damage the system board.
5. Remove the jumper from pins 1 and 2. Place the jumper on pins 2 and 3.
6. Place the jumper back on pins 1 and 2.
7. Replace the access panel.
8. Reconnect the external equipment.
POST Error Messages
9. Plug in and turn on power.
• Time & Date Not Set.
NOTE: You will receive POST error messages after clearing CMOS and rebooting
Press
advising you that configuration changes have occurred. Use Computer Setup to reset
• 511-CPU fan not detected.
any special system setups along with the date and time.
Press
• Keyboard Error.
Without press any key, PC will continue boot.
Hewlett-Packard Vision Diagnostics
• 1720-SMART Hard Drive detects imminent failure. Failing Drive: SATA# Failing
The Hewlett-Packard Vision Diagnostics utility allows you to view information about the
Attribute: #.
hardware configuration of the computer and perform hardware diagnostic tests on the
Press
subsystems of the computer. The utility simplifies the process of effectively identifying,
• ERROR: No boot disk has been detected or the disk has failed.
diagnosing, and isolating hardware issues.
When no boot device was detected or all detected devices failed to boot, the
Use HP Vision Diagnostics to determine if all the devices installed on the computer are
BIOS will display the above message and stop.
recognized by the system and functioning properly.
• (ERROR: Unsupported CPU installed.
To access HP Vision Diagnostics, you must create a Recovery Disc Set then boot to the
Press
CD containing the utility. It can also be downloaded from http://www.hp.com and
either burned to CD or installed to a USB flash drive.
Downloading the Latest Version of HP Vision Diagnostics
POST Audible Codes
1. Go to http://www.hp.com.
2. Click the Software & Drivers link.
3. Select Download drivers and software (and firmware).
Pattern
Meaning
Recommended Action
4. Enter your product name in the text box and press the Enter key.
3 times: Once every second,
Unsupported
1. Upgrade the BIOS to proper
5. Select your specific computer model.
followed by a two second pause. CPU installed. version.
6. Select your OS.
2. Change the processor.
7. Click the Diagnostic link.
4 times: Once every second,
Power supply Check if the Power supply is
8. Click the Hewlett-Packard Vision Diagnostics link.
followed by a two second pause. failure.
work well.
Beeps stop after fifth iteration but
9. Click the Download button.
LEDs flashes continue until problem
NOTE: The download includes instructions on how to create the bootable CD.
is solved.
5 times: Once every second,
Pre-video
Check if the memory modules
Microsoft System Restore
followed by a two second pause. memory error. have been installed correctly
If you have a problem that might be due to software that was installed on your computer,
Beeps stop after fifth iteration but
and that proper modules are
use System Restore to return the computer to a previous restore point. You can also set
LEDs flashes continue until problem
used.
is solved.
restore points manually.
6 times: Once every second,
Pre-video
For systems with a graphics
NOTE: Always use this System Restore procedure before you use the System Recovery
followed by a two second pause. graphics error. card:
program.
Beeps stop after fifth iteration but
1. Reseat the graphics card.
NOTE: Some features might not be available on systems that are shipped without a
LEDs flashes continue until problem
Power on the system.
version of Microsoft Windows.
is solved.
2. Replace the graphics card.
To start a System Restore:
3. Replace the system board.
1. Close all open programs.
For systems with integrated
2. Click the Start button, right-click Computer, and then click Properties.
graphics, replace the system
board.
3. Click System protection, System Restore, click Next, and then follow the
on-screen instructions.
7 times: Once every second,
System board Check if the board HW is OK.
To add restore points manually:
followed by a two second pause. failure.
1. Close all open programs.
Beeps stop after fifth iteration but
LEDs flashes continue until problem
2. Click the Start button, right-click Computer, click Properties, and then click
is solved.
System protection.
3. Under Protection Settings, select the disk for which you want to create a restore
8 times: Once every second.
Invalid ROM
Upgrade the BIOS with proper
Beeps and LED flashes stop after image
version.
point.
first iteration.
detected.
4. Click Create, and then follow the on-screen instructions.
System Recovery
System Recovery completely erases and reformats the hard disk drive, deleting all data
files you have created, and then reinstalls the operating system, programs, and drivers.
However, you must reinstall any software that was not installed on the computer at the
factory. This includes software that came on media included in the computer accessory
box, and any software programs instal ed after purchase.
You must choose one of the following methods to perform a System Recovery:
• Recovery Image. Run the System Recovery from a recovery image stored on your hard
disk drive. The recovery image is a file that contains a copy of the original
factory-shipped software.
NOTE: The recovery image uses a portion of the hard disk drive that cannot be used
for
data storage.
• Recovery Discs. Run the System Recovery from a set of recovery discs that you create
from files stored on your hard disk drive or purchased separately.
HP/Compaq 100B Illustrated Parts & Service Map, SFF chassis 656508-002 Page 3
...
Компьютеры - Compaq 100B Small Form Factor PC (297.44 kb)
Компьютеры - Compaq 100B Small Form Factor PC (ENERGY STAR) (297.44 kb)
Компьютеры - HP 100b Desktop PC series (297.44 kb)
Компьютеры - HP e-PC c10/s10 (297.44 kb)