Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
8. Your motherboard is now installed. Power/LED Connections The Antec TruePower power supply is an ATX12V form factor power supply. An ATX12V power supply has a single 20-pin Main Power Connector, a 6-pin AUX Power Connector, and a 4-pin +12V Power Connector for the motherboard. It also comes with five to seven 4-pin Peripheral Power Connectors and one to two 4-pin Floppy Drive Power Connectors for your drives. It is backwards-compatible to previous ATX form factor power supplies. If your motherboard does not support the AUX Power Connector or the +12V Power Connector, you can still use this power supply. The TruePower power supply is also equipped with a 3-pin fan signal connector. Connect it to one of the fan connectors on your motherboard. You may monitor the speed of the power supply rear fan through your motherboard BIOS or through the monitoring software that comes with your motherboard. Note: The speed of the fan may be as low as 1500 RPM when temperatures are low. At these speeds some motherboards may not be able to properly detect the fan speed and may generate false warnings of fan failure. Please refer to your motherboard manual for proper fan monitoring set up. 1. Connect the 20-pin ATX power connector (and AUX or +12V connectors if appropriate) to your motherboard. 2. Reset (labeled RESET SW) connects to your motherboard at the RST connector. The label should be facing the front of the case, and for all of the following connectors as well. 3. Power LED (labeled POWER LED) connector is located behind the Reset connector. 2 4. Power Switch motherboard. 5. Speaker (labeled 6. Hard Drive LED 7. LED I, LED II connectors: This case comes with LED II. You may use these LED LED (blinks when your modem USB Connection There are 8 wires with connectors 1. Locate the internal USB header pins They should consist of 10-pins in two rows. Note: On some motherboards one or two pins may This indicates no contact. It is an empty pin. You don't need to use it. On some motherboards one pin may be missing on either one or both rows. Don't worry about it. You only need 8 pins to connect to. 2. Consult your motherboard manual to get each of the 3. Power Pins: There are two power pins, one on each row. They are usually marked as Power, Vcc or +5V. Connect the two +5V connectors to the two power pins. Each connector can go to either pin. 4. Ground Pins: There are two ground pins, one on each row. They are usually marked as GROUND or GND. Connect the two GROUND connectors to the two ground pins. Each connector can go to either pin. Note: On some motherboards, there may be two ground pins on one row. You don't need to use all of them. Make sure to connect one ground pin on each row. 5. Data Pins: There are two plus data pins, one on each row, and two minus data pins, one on each row. They are usually marked as USBD2+, USBD3+ and USBD2-, USBD3- or USBP2+, USBP3+, and USBP2-, USBP3- respectively. a. Connect the 1 +D connector to any of the two plus data pins. It can go to either of the plus pins. b. Connect the 1 -D connector to the minus data pin in the same row as the plus data pin that 1 +D connector has just connected to. c. Repeat the same procedures to connect the 2 +D and 2 -D to the motherboard. Make sure they are in the same row. IEEE1394 (FireWire, I-Link) Connection There are six wires with connectors coming from the front mounted IEEE1394 port of your case. They consist of 2 sets of twisted pair cables; TPA ( Twisted Pair A) and TPB (Twisted Pair B), a power cable (VP), and a ground cable (VG). 1. Locate and identify the pin-out of the IEEE1394 port on your motherboard. 2. Power Pin: Connect the VP connector to it. 3. Ground Pin: Connect the VG connector to it. 4. Data Pins: There are two sets of data pins. Each set consists of a plus and a minus pin. They are usually marked as TPA+ and TPA-, TPB+ and TPB-. a. Connect the TPA+ connector to the TPA+ data pin and TPA- connector to the TPA- data pin. b. Connect the TPB+ connector to the TPB+ data pin and TPB- connector to the TPB- data pin. 3.5" Device With the front You can see four 5.25" and Inside the case there 1. Pull the quick release Looking from the rear (external) drive bays. Carefully put a screwdriver push the plastic drive bay cover Carefully use your hands to the metal plate back and forth Note: Don't take off the covers and plates for the drive now. Be careful of the newly exposed metal areas are likely to be sharp. 2. Install your floppy drive into the top drive 3. Mount your other 3.5" device into the drive cage. 4. Slide and lock the drive cage back into the case. 5. Release the second cage. Note: Inside the cage you will find a fan bracket. This is for one of the optional 80mm cooling fans. If you want to install the optional fan you should do it now. For fan installation please see the Fan Installation section of 6. Mount your other 3.5" devices into the drive cage. 7. Slide and lock the drive cage back into the case. 8. Find a small 4-pin white ...