Оценок - 4, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Ноутбуки - VGC-LV2SRJ (3.02 mb)
Ноутбуки - VGC-LV2SRJ (3.94 mb)
Ноутбуки - VGC-LV2SRJ (2.95 mb)
Ноутбуки - VGC-LV2SRJ (1.43 mb)
Фрагмент инструкции
. Use only the supplied AC adapter or power cord for your computer. To connect the power cord or the AC adapter and other cables 1 Remove the back panel cover and the base stand cover from the computer. See Removing and Replacing the Covers (page 21) for the procedure. 2 Connect a power cord or an AC adapter to the computer. . VGC-LN series models 1 Plug one end of the power cord (1) into the AC adapter (3) and the other end into AC outlet (2). 2727nNGetting Started 2 Put the cable connected to the AC adapter through the hole (4) in the base stand and plug it into the DC IN port (5) as illustrated below. ! The shape of the DC In plug varies depending on the AC adapter. Be sure to push the plug all the way in. n 28 N Getting Started . VGC-LV series models Plug one end of the power cord (6) into the AC outlet (7), put the other end through the hole (8) in the base stand, and plug it into the AC In port (9) on the computer as illustrated below. !B e sure to push the plug into the AC In port all the way to the guide line (10). n2299 NGetting Started 3 Connect other cables to the computer, if necessary. . To set up TV connections, see Using the TV Function (page 62). . To connect an HDMI cable to the HDMI INPUT port for using the HDMI Input function, see Using the HDMI Input Function (page 71). . To connect your computer to an Ethernet network, see Using the Network (LAN) (page 92). 4 Slightly pull the tab (11) of the cable clamp (12) with your fingertip in the direction of the arrow and gently pull it up to release the cable clamp. Route the cable(s) through the cable clamp and then snap the cable clamp back shut. 3030nNGetting Started Replace the stand cover and the back panel cover. See Removing and Replacing the Covers (page 21) for the procedure. . To disconnect your computer completely from AC power, unplug the power cord or the AC adapter when the computer is off. Make sure that the AC outlets are easily accessible. ! If you unplug the power cord or the AC adapter from your computer while the computer is on or in Sleep mode, you may lose all unsaved data. 3131nNGetting Started Connecting the Wireless Keyboard A wireless keyboard and four AA alkaline batteries for use in the keyboard are supplied with your computer. Before attempting to use the wireless keyboard, you must install the batteries and establish communication between the computer and the keyboard. . If you find your keyboard not working, for example after replacing the keyboard batteries, try the following steps for reconnection. To connect the wireless keyboard ! To connect the wireless keyboard, it must be located within a range of 30 cm to 1 m from the computer. 1 Insert the supplied four AA batteries (1) into the battery compartment (2) on the bottom of the wireless keyboard. 2 Turn on the computer. 3 Slide the power switch (3) on the back of the keyboard to the ON position. 4 Press the CONNECT button (4) on the back of the computer. 5 Press the CONNECT button (5) on the bottom of the keyboard. The connect indicator turns on in the LCD window on the keyboard when connection is established between the computer and the keyboard. If not, repeat the procedure. ! Steps 4 and 5 must be completed within 10 seconds of each other. If the wireless keyboard is left unused for 20 minutes or longer, the connect indicator will turn off to conserve battery power. This indicates that the connection between your computer and the keyboard is lost. Press the Fn key to check that the connect indicator turns on before using the keyboard. 3232nNGetting Started . You can check the battery indicator ( or ) in the LCD window on the wireless keyboard for its battery power level. If the wireless keyboard does not operate properly, the batteries may need to be replaced. If you do not intend to use the wireless keyboard for an extended period of time, remove the batteries to avoid possible damage from battery leakage. If you want to put the wireless keyboard in a more 'ergonomic' position, flip open the keyboard feet. 3333nNGetting Started Connecting the Wireless Mouse A wireless mouse and two AA alkaline batteries for use in the mouse are supplied with your computer. Before attempting to use the wireless mouse, you must install the batteries and establish communication between your computer and the mouse. . If you find your mouse not working, for example after replacing the mouse batteries, try the following steps for reconnection. To connect the wireless mouse ! To connect the wireless mouse, it must be located within a range of 30 cm to 1 m from the computer. Insert the supplied two AA batteries into the wireless mouse as shown below: Turn on the computer. 3434nNGetting Started Slide the power switch on the bottom of the mouse to the ON position. Press the CONNECT button (1) on the back of the computer. Press the CONNECT button on the bottom of the mouse within 10 seconds from step 4. Communication between the mouse and the computer should now be established. . If t...
Эта инструкция также подходит к моделям:Компьютеры - VGC-LN2M (7.78 mb)
Компьютеры - VGC-LN2MR (7.78 mb)
Компьютеры - VGC-LV2J (7.78 mb)
Компьютеры - VGC-LV2SJ (7.78 mb)