Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Компьютеры - Intel® Desktop Board DQ67EP (1.15 mb)
Компьютеры - Intel® Desktop Board DQ67EP (51.99 kb)
Фрагмент инструкции
3. Remove the computer’s cover and locate the DIMM sockets (see Figure 15). 4. If a full length PCI Express graphics card is installed in the PCI Express x16 connector, remove the card to gain full access to the DIMM sockets. Figure 15. Installing a DIMM 5. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 6. Holding the DIMM by the edges, remove it from its anti-static package. 7. Position the DIMM above the socket. Align the small notch at the bottom edge of the DIMM with the keys in the socket (see inset in Figure 15). 8. Insert the bottom edge of the DIMM into the socket. 9. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 10. Reinstall the PCI Express graphics card if one was removed in Step 4. 11. Replace the computer’s cover and reconnect the AC power cord. Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 33. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the AC power cord from the computer. 4. Remove the computer’s cover. 5. If a full length PCI Express graphics card is installed in the PCI Express x16 connector, remove the card to gain access to the DIMMs. 6. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops out of the socket. 7. Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static package. 8. Reinstall the PCI Express graphics card if one was removed in Step 5 and reconnect any other parts you removed or disconnected to reach the DIMMs. 9. Replace the computer’s cover and reconnect the AC power cord. Installing and Removing PCI Express x16 Graphics Cards Installing a PCI Express x16 Graphics Card CAUTION When installing a PCI Express add-in card, ensure that the card is fully seated in the PCI Express connector before you power on the system. If the card is not fully seated in the connector, an electrical short may result across the connector pins. Depending on the over-current protection of the power supply, certain Desktop Board components and/or traces may be damaged. CAUTION Before installing a PCI Express add-in card, make sure that it will not touch the processor heatsink. This might cause an electrical short and damage the graphics card and/or the desktop board. CAUTION Before installing a PCI Express add-in card, make sure that the tabs on the DIMM sockets are in the upright position (closed); otherwise, they may be damaged by the PCI Express card during installation. Intel Desktop Board DQ67EP Product Guide Follow these instructions to install a PCI Express x16 graphics card: 1. Observe the precautions in "Before You Begin" on page 33. 2. Place the card in the PCI Express x16 connector (Figure 16, A) and press down on the card until it is completely seated in the connector and the card retention notch on the card snaps into place around the retention mechanism pin on the connector. 3. Secure the card’s metal bracket to the chassis back panel with a screw (Figure 16, B). 4. Connect a monitor to the graphics card according to the manufacturer’s instructions. Figure 16. Installing a PCI Express x16 Graphics Card Installing and Replacing Desktop Board Components Removing a PCI Express x16 Graphics Card Follow these instructions to remove a PCI Express x16 graphics card from a connector: 1. Observe the precautions in "Before You Begin" on page 33. 2. Disconnect the monitor cable from the graphics card back panel connector. 3. Remove the screw (Figure 17, A) that secures the card’s metal bracket to the chassis back panel. 4. Push the card ejector lever down using the tip of a pencil or similar tool (Figure 17, B) in the notch. This will release the card from the connector (C). 5. Pull the card straight up to remove it. Figure 17. Removing a PCI Express x16 Graphics Card Intel Desktop Board DQ67EP Product Guide Installing a Wireless LAN Card in the PCI Express Half-Mini Card Slot (Optional) A wireless LAN card can be installed in the Desktop Board’s PCI Express Half-Mini Card slot. Wireless LAN cards are not included with the Desktop Board and must be purchased separately. To install a PCI Express Half-Mini Card wireless LAN card on the Desktop Board, see Figure 18 and follow these steps: 1. Observe the precautions in "Before You Begin" on page 33. 2. Locate the PCI Express Half-Mini Card slot (see Figure 1, G). 3. Insert the wireless LAN card into the PCI Express Mini Card connector (Figure 18, A) at a slightly upward angle. 4. Align the mounting holes (Figure 18, B) and snap the card in place. 5. Attach your system’s antenna wires to the connectors (Figure 18, C) on the wireless LAN card as shown. Figure 18. Installing a Wireless LAN Card Installing and Replacing Desktop Board Components Connecting Serial ATA (SATA) Cables SATA ...