Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
12. Replace the front panel (see Replacing the Front Panel). 13. Replace the computer cover (see Replacing the Computer Cover). 14. Connect your computer and devices to their electrical outlets, and turn them on. Replacing the FlexDock 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover). 3. Remove the front panel (see Replacing the Front Panel). 4. Disconnect the FlexDock USB cable from the back of the FlexDock and from the internal USB connector (F_USB1) on the system board (see System Board Components). 5. Remove the two screws securing the FlexDock. 6. Slide the FlexDock out through the front of the computer. 7. If you are not replacing the FlexDock, replace the drive panel insert (see Replacing the Drive Panel Insert). 8. If you are installing a new FlexDock: a. Remove the drive panel insert, if applicable (see Replacing the Drive Panel Insert). b. Remove the FlexDock from its packaging. 9. Gently slide the FlexDock into place in the FlexDock slot. 10. Align the screw holes in the FlexDock with the screw holes in the FlexDock. 11. Replace the two screws that secure the FlexDock. 12. Connect the FlexDock USB cable to the back of the FlexDock and to the internal USB connector (F_USB1) on the system board (see System Board Components). NOTE: If you installed a new drive, see the documentation that came with the drive for instructions on installing any software required for drive operation. 1 custom screws (2) 2 F_USB1 connector 3 FlexDock USB cable 4 FlexDock NOTE: Ensure that the FlexDock is installed before the FlexDock cable is connected. 13. Replace the front panel (see Replacing the Front Panel). 14. Replace the computer cover (see Replacing the Computer Cover). 15. Connect your computer and devices to electrical outlets, and then turn them on. Removing the FlexDock Break-Away Metal Plate Align the tip of a Phillips screwdriver with the slot on the break-away metal plate and rotate the screwdriver outwards to break and remove the metal plate. Replacing the FlexDock Drive Inserts 1. Remove the front panel (see Replacing the Front I/O Panel). 2. Gently press on the insert lever outward to release the lock. 3. Pull the FlexDock drive insert away from the front panel. 4. To replace the FlexDock drive insert, align the FlexDock drive insert in place. 5. Push the insert lever towards the front panel till it snaps in place. Replacing the Drive Panel Insert Align the drive panel insert along the edges of the empty slot of the FlexDock or CD/DVD drive and push the panel insert and push the panel insert until it locks in place. NOTICE: To comply with FCC regulations, it is recommended that you replace the FlexDock drive insert whenever the FlexDock drive is removed from the computer. 1 front panel 2 insert lever 3 FlexDock drive insert Replacing the Media Card Reader 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover). 3. Remove the front panel (see Replacing the Front Panel). 4. Remove any expansion cards (see Replacing a PCI/PCI Express Card). 5. Disconnect the cable that is connected to the mediacard reader from the system board (F_USB4). 6. Remove the screw that secures the Media Card Reader to the chassis. 7. Carefully remove the existing Media Card Reader from the computer. 8. To install a new Media Card Reader, align and slide the Media Card Reader clamp into the Media Card Reader clamp slot. 9. Replace and tighten the screw that secures the Media Card Reader to the chassis. 10. Reconnect the cables to the system board. NOTICE: To comply with FCC regulations, it is recommended that you replace the drive panel insert whenever the FlexDock is removed from the computer. 1 back of the computer 2 drive panel insert (optional) NOTICE: Carefully note the routing of each cable before you disconnect it, so that you are sure to re-route cables correctly. An incorrectly routed or a disconnected cable could lead to computer problems. 1 screw 2 Media Card Reader 3 Media Card Reader clamp 11. Replace any expansion cards (see Replacing a PCI/PCI Express Card). 12. Replace the front panel (see Replacing the Front Panel). 13. Replace the computer cover (see Replacing the Computer Cover). 14. Connect your computer and devices to an electrical outlet, and turn them on. Back to Contents Page Back to Contents Page Replacing Fans Dell Studio™ 540 Service Manual Replacing the Chassis Fan Replacing the Processor Fan and Heat Sink Assembly Replacing the Chassis Fan 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover). 3. Disconnect the chassis fan cable from the system board connector (SYS_FAN1). 4. Remove the four screws securing the chassis fan. 5. Lift the chassis fan away from the computer. 6. To replace the chassis fan, slide it in place towards the back of the computer. 7. Replace the four screws to secure the chassis fan. 8. Connect the chassis fan cab...