Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
1 Shut down the computer through the Start menu. 2 Ensure that your computer and attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your computer, turn them off now. NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3 Disconnect any telephone or telecommunication lines from the computer. 4 Disconnect your computer and attached devices from their electrical outlets, and then press the power button to ground the system board. 5 Remove the computer from the mounting plate (if used). 6 Remove the cable cover, if it is attached. 7 Remove the stand, if it is attached. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. NOTICE: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components. 8 Remove the following components in the order in which they are listed (for detailed removal steps, see the User’s Guide): a Module device b Hard drive c Computer cover Re placing the System Board 3 0Y0561.book Page 4 Thursday, May 8, 2003 9:45 AM | support.dell.com d Heat-sink fan shroud e Heat sink f Chassis intrusion switch 9 Remove the heat-sink retention base by removing the four green screws that secure the retention base to the chassis. 10 Remove the five silver screws that secure the system board to the chassis. silver system board green retention screws (5) base screws (4) NOTICE: The module device connector is attached underneath the system board. When removing the system board, be careful not to bump or catch the connector on the metal chassis floor. 4 Re placing the System Board Replacing the System Board 5 11 Remove the system board and I/O shield assembly by slightly sliding the board toward the front of the computer and lifting up. 12 Remove the two black screws that secure the I/O shield to the system board. 0Y0561.book Page 5 Thursday, May 8, 2003 9:45 AM 0Y0561.book Page 6 Thursday, May 8, 2003 9:45 AM | support.dell.com 13 Remove the I/O shield: a Turn the system board upside down. b Carefully insert a blunt, nonconducting object such as a plastic screwdriver under the I/O shield and pry the shield away from the system board until the shield dislodges from the system board. 14Attach the I/O shield to the replacement system board: aAlign the two flanged screw mounts on the I/O shield with the two screw holes on the system board. bRotate the I/O shield toward the system board and snap the I/O shield into place. cReplace the two screws that you removed in step 12. 6 Replacing the System Board Replacing the System Board 7 15 Install the replacement system board and I/O shield assembly: a Line up the parallel port connector with the opening on the back of the computer. b Insert the back-panel connectors into the openings at the back of the computer and lower the system board into place. 0Y0561.book Page 7 Thursday, May 8, 2003 9:45 AM 0Y0561.book Page 8 Thursday, May 8, 2003 9:45 AM c Replace the five silver screws that you removed in step 10. d Reinstall the heat sink retention base by reinserting the four green screws that you removed in step 9. e Replace all of the components that you removed in step 8. 16 Reattach the stand (if used). 17 Attach the computer to the mounting plate (if used). 18 Replace the cable cover (if used). NOTICE: To connect a network cable, first plug the cable in to the network wall jack and then in to the computer. 19 Connect your computer to the adapter cable and to an electrical outlet, connect any devices to electrical outlets, and then turn on the computer and devices. After you replace the cover, the chassis intrusion detector, if enabled, causes the following message to appear on the screen at the next computer start-up: ALERT! Cover was previously removed. 20 Reset the chassis intrusion detector by changing the Chassis Intrusion option to Enabled or Enabled-Silent. | support.dell.com 8 Re placing the System Board 0Y0561.book Page 9 Thursday, May 8, 2003 9:45 AM Dell™ Computers Remplacement de la carte systeme | support.dell.com 0Y0561.book Page 10 Thursday, May 8, 2003 9:45 AM Remarques, avis et precautions REMARQUE : Une REMARQUE fournit des informations importantes qui vous aident a mieux utiliser votre ordinateur. AVIS : Un AVIS vous avertit d'un risque de dommage materiel ou de perte de donnees et vous indique comment eviter le probleme. PRECAUTION : Une PRECAUTION indique un risque potentiel d'endommagement du materiel, de blessure corporelle ou de mort. Les informations contenues dans ce document sont sujettes a modification sans preavis. © 2002–2003 Dell Computer Corporation. Tous droit...