Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
You can do so by touching an unpainted metal surface on the computer chassis. 1 Media Card Reader 2 screw (3) 5. Remove the Media Card Reader and bracket from its packaging. 6. Ensure that the Media Card Reader is installed before the FlexBay USB cable is connected. 7. Make sure the FlexBay USB cable is connected to the back of the Media Card Reader. 8. Insert the Media Card Reader by sliding and holding the drive latch release downward. Then, slide the drive in to seat it in the computer. 9. Route the USB cable through the cable routing clip. 10. Replace the computer cover. CD/DVD Drive Removing a CD/DVD Drive 1. Follow the procedures in "Before you Begin." 2. Remove the computer cover. 3. Remove the drive panel. 4. Disconnect the power and data cables from the back of the drive. NOTE: Connect the USB cable on the back of the Media Card Reader to the front panel USB connector on the system board. 1 Media Card Reader 2 FlexBay cables CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. 5. Remove the CD/DVD drive by sliding and holding the drive latch release downward. Then, slide the drive out of the computer. Installing a CD/DVD Drive 1. Follow the procedures in "Before you Begin." 2. If you are installing a new CD/DVD drive rather than replacing a drive, remove the drive- panel inserts. 3. Gently slide the drive into place until it clicks or you feel the drive securely installed. 1 data cable 2 power cable 1 sliding plate lever 2 sliding plate 3 CD/DVD drive 4. Connect the power and data cables to the drive. 5. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 6. Replace the computer cover. 7. Replace the drive panel. 8. Connect your computer and devices to their electrical outlets, and turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation. 9. Enter system setup and select the appropriate Drive option. NOTE: If you are installing a new CD/DVD drive rather than replacing a drive, remove the drive panel inserts and slide the drive into place. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 1 drive 2 screw (3) 1 data cable 2 power cable NOTICE: To connect a network cable, first plug the cable in to the network device and then plug the cable in to the computer. 10. Verify that your computer works correctly by running the Dell Diagnostics. Processor Removing the Processor 1. Follow the procedures in "Before you Begin." 2. Loosen the two captive screws on each side of the heat sink assembly. 3. Rotate the heat sink assembly upward, and remove it from the computer. 4. Open the processor cover by sliding the release lever from under the center cover latch on the socket. Then, pull the lever back to release the processor. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. CAUTION: Despite having a plastic shield, the heat sink assembly may be very hot during normal operation. Be sure that it has had sufficient time to cool before you touch it. 1 heat sink and fan shroud assembly 2 captive screw housing (2) NOTICE: If you are installing a processor upgrade kit from Dell, discard the original heat sink. If you are not installing a processor upgrade kit from Dell, reuse the original heat sink when you install your new processor. 1 processor cover 2 processor 3 socket 5. Gently remove the processor from the socket. Leave the release lever extended in the release position so that the socket is ready for the new processor. Installing the Processor 1. Unpack the new processor, being careful not to touch the underside of the processor. 2. If the release lever on the socket is not fully extended, move it to that position. 3. Orient the front and rear alignment notches on the processor with the front and rear alignment notches on the socket. 4. Align the pin-1 corners of the processor and socket. 5. Set the processor lightly in the socket and ensure that the processor is positioned correctly. 6. When the processor is fully seated in the socket, close the processor cover. Ensure that the tab on the processor cover is positioned underneath the center cover latch on the socket. 7. Pivot the socket release lever back toward the socket and snap it into place to secure the processor. If you installed a processor replacement kit from Dell, return the original heat sink assembly and processor to Dell in the same package in which your replacement kit was sent. 8. Install the heat sink assembly: 4 release lever NOTICE: When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the s...