Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
5. Lift the four fastner caps to release the processor heat sink assembly from the system board. 6. Lift the processor fan and heat sink assembly out of the computer. Replacing the Processor Fan and Heat Sink Assembly 1. Follow the procedures in Before You Begin WARNING: Despite having a plastic shield, the processor fan and heat sink assembly may be very hot during normal operation. Ensure that it has had sufficient time to cool before you touch it. CAUTION: The processor fan and heat sink assembly is a single unit. Do not try to remove the fan separately. CAUTION: When you remove the processor fan and heat sink assembly, lay it upside down or on its side to avoid damaging the heat sink thermal interface. 1 flat-blade screwdriver 2 system board connector 3 slot 4 fastner caps (4) 5 processor fan and heat sink assembly 2. Clean the thermal grease from the bottom of the heat sink. 3. Apply new thermal grease to the top of the processor. 4. If required, rotate the fastner caps on the processor heat sink assembly clockwise to ensure that they are in lock position. 5. Align and press the four fastner caps on the processor fan and heat sink assembly into the screw holes on the system board. 6. Connect the processor fan and heat sink assembly cable to the system board connector (see System Board Components). 7. Replace the computer cover (see Replacing the Computer Cover). 8. Connect your computer and devices to electrical outlets, and turn them on. Back to Contents Page CAUTION: Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a requirement for optimal processor operation. Back to Contents Page Front USB Panel Dell™ Studio XPS™ 8100 Service Manual Removing the Front USB Panel Replacing the Front USB Panel Removing the Front USB Panel 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the front bezel (see Removing the Front Bezel). 4. Disconnect the front USB panel cables from the system board connectors (see System Board Components). 5. Remove the screw that secures the front USB panel to the front panel. 6. Slide the front USB panel down to release the clamps from the front panel and pull it away. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at WARNING: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. WARNING: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. NOTE: Make note of the routing of all cables as you remove them so that you can re-route them correctly when installing the new front USB panel. CAUTION: When sliding the front USB panel out of the computer, be extremely careful. Carelessness may result in damage to the cable connectors and the cable routing clips. 1 front USB panel clamp slot 2 front USB panel 3 screw Replacing the Front USB Panel 1. Follow the procedures in Before You Begin. 2. Align and slide the front USB panel clamp into the front USB panel clamp slot. 3. Replace the screw that secures the front USB panel to the front panel. 4. Connect the front USB panel cables to the system board connectors (see System Board Components). 5. Replace the front bezel (see Replacing the Front Bezel). 6. Replace the computer cover (see Replacing the Computer Cover). 7. Connect your computer and devices to electrical outlets, and turn them on. Back to Contents Page CAUTION: Take care not to damage the cable connectors and the cable routing clips when sliding the front USB panel into the front USB panel clamp slot. Back to Contents Page Graphics Card Bracket Dell™ Studio XPS™ 8100 Service Manual Removing the Graphics Card Bracket Replacing the Graphics Card Bracket Removing the Graphics Card Bracket 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the two screws that secure the graphics card bracket to the drive panel. 4. Pivot the graphics card bracket up and lift it off the hinge clamp slot. 5. Set the graphics card bracket aside in a secure location. Replacing the Graphics Card Bracket 1. Follow the procedures in Before You Begin. 2. Align and insert the hinge clamp on the graphics card bracket into the hinge clamp slot on the chassis. 3. Pivot the graphics card bracket downward. 4. Replace the two screws that secure the graphics card bracket to the drive panel. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety ...