Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover). 3. Gently securing both graphics cards with one hand, remove the graphics card bridge (if present) with your other hand by pulling it up and away from the computer. Set it aside. Repeat if removing two bridges from a triple card configuration. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTE: If a graphics card is installed in each of the PCIe x16 card slots in the multi-graphics configuration, the PCIe x1 and one PCI card slot are not accessible for use. 1 PCI card 2 PCIe x1 card 3 PCIe x1 card slot 4 PCIe x16 card slot 5 PCIe x16 card NOTE: This section deals with dual and triple configurations of PCIe x16 graphics cards only. For removal of any other type of PCI or PCIe cards, see Replacing the PCI and PCI Express Cards. 1 graphics card bridge 2 power connectors (2) 3 dual-PCIe graphics cards 4. Disconnect any cables connected to the card. 5. Remove the captive screws on top of the PCI card fan shroud and remove the shroud. 6. Remove the card retention screw(s) on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis wall. 7. Press the securing tab (if present) on the system board connector as you grasp the card by its top corners, and then ease the card straight out of the connector . 8. Install a filler bracket in the empty card-slot opening. If you are replacing the card, see Installing Graphics Cards for Multi Graphics Card. 9. Replace the PCI card fan shroud, replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on. Installing Graphics Cards for Multi Graphics Card This section pertains to using dual and triple PCIe graphics cards to take advantage of NVIDIA's SLI (Scalable Link Interface). For installation of other types of PCI or PCIe cards, see Replacing a PCI/PCI Express Card. 1 retention screw 2 card retainer 3 alignment guide 4 fan bracket 1 PCIe x16 card 2 securing tab 3 PCIe x16 card slot NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer. NOTE: The graphics card bridge (not present in all multi-graphics configurations) is not necessary in a single graphics card configuration. CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. NOTE: To upgrade to or downgrade from a dual- or triple-graphics card configuration, you may need additional parts that can be ordered from Dell. Some expansion card slots will not be available for use if a dual-slot graphics card is installed in any of the PCIe x16 card slots. If you are upgrading from a single-slot graphics card to a dual-slot graphics card, you will need to remove any card installed in these expansion slots. To remove a PCIe card, see Replacing the PCI and PCI Express Cards. 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover). 3. Remove the captive screws on top of the PCI card fan shroud and remove the shroud. 4. Remove the filler bracket or existing graphics card to create a card-slot opening. 5. Install two SLI-ready graphics cards into the two outer PCIe x16 slots on the system board. 6. Prepare the cards for installation. See the documentation that came with the cards for information on configuring them, making internal connections, or otherwise customizing them for your computer. 7. Position each card so that it is aligned with the slot and that the securing tab (if present) is aligned with the slot. CAUTION: For information about upgrading your system to use NVIDIA SLI (Scalable Link Interface) multi-graphics technology, see the Dell support website at support.dell.com. NOTE: If you are upgrading to a multi-graphics card configuration and have a card installed in the PCIe x1 card slot, remove the card (see Replacing the PCI and PCI Express Cards). 1 retention screw 2 card retainer 3 alignment guide 4 fan bracket NOTE: If the card is full length, insert the card guide into the alignment slot on the fan bracket. 1 PCIe x16 card 2 securing tab 3 PCIe x16 card slot CAUTION: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board. Gently pull the securing tab (if present) and place the card in the connector. Press down firmly and ensure that the card is fully seated in the slot. 8. Screw in the card retention screw(s) on the top of the card retainer at the appropriate card slot. 9. Repeat for additional graphics cards. Connect the PC...
Эта инструкция также подходит к моделям:Компьютеры - XPS 730 H2C (2.32 mb)