Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
To install the peripheral, please go through the following steps. Note!! Before installing the expansion card, please check the card size limitation. Size limitation for standard riser card is 182mm; and the size limitation for low profile riser card is 182mm. Step 1 Loosen the riser bracket screws. Step 2 Lift the riser bracket slightly, then pull it out from the server chassis. Step 3 Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Align the riser bracket to the system module. 2 4 1 3 1 16 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 3 Slide hard disk into blank. Step 4 Secure it with screws. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 17 GS-R1233-RH Rack Mount Server Guiding groove Step 2-7: FAN Duct Removal and Installation Step 1 Align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. System Appearance 18 3-1: Front View of GS-R1233-RH Chapter 3 Appearance of GS-R1233-RH .. .. .. .. .. Hot-Swap SATA HDDs USB connectors Front panel switch and LEDs .. 3-2: Rear View of GS-R1233-RH .. .. .... .... .. .. .. .. .. .. .... .. Power cord Mouse connector Keyboard connector COM port VGA port USB connectors RJ45 LAN ports Low-profile riser slot .. GS-R1233-RH Rack Mount Server 3-3: Front Bazel Switch and LED Indicators Introduction LAN1/2 Activities Power ID BTN&LEDSystem LED HDDReset switch NMI switch Name Color Condition Description Power Green On Power On Green Blink Sleep (S1) -Off Power Off (S4) SYS (System) Amber Blink System Ready but degraded, CPU Failed, DIMM Killed Amber On Critical Alarm: Critical Power Module Failure, Critical FANs Failure, Voltage (Power Supply) Critical Teemperature and Voltage -Off System healthy. HDD Green Blink Hard Disk Drive Access -Off No Access and No HDD Fault LAN1 Activity Green On LAN Link / No access Green Blink LAN access -Off Idle LAN2 Activity Green On LAN Link / No access Green Blink LAN access -Off Idle ID (Identification) Blue On Unti selected for identification -Off No identification 19 LED Description 3-4: LAN LED Description NameColor Condition Description LANGreen O N LAN Link / no Access GreenLink/ActivityBLINK LAN Access -OFF Idle 10 LAN-OFF 10Mbps connection Speed 100 LANGreen O N 100Mbps connection SpeedGreen BLINK Port identification with 10 or 100Mbps connection GbE LANYellow O N 1Gbps connection Speed Yellow BLINK Port identification with 1Gbps connection 20 GS-R1233-RH Rack Mount Server 3-5: Back plane board Information Hard Disk Drive 1Hard Disk Drive 2Hard Disk Drive 3Hard Disk Drive 4 3-6: Hard Disk Drive LED Description Hard Disk LED Color Condition Description Green Blink Hard Disk Drive Access -Off No Access and No HDD Fault 21 Connector Icon Description 3-7: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 GS-R1233-RH Rack Mount Server Chapter 4 Motherboard Connectors Introduction and Jumper Setting 2 1 3 4 5 76 9 11 10 8 1. ATX_L1 6. SATA3 (SATA data cable connector) 2. ATX_12V1 7. SATA2 (SATA data cable connector) 3. F_USB1 (Front USB cable connector) 8. BP2 4. SATA0 (SATA data cable connector) 9. F_PANEL1 5. SATA1 (SATA data cable connector) 10. JP1 (Jumper Block) 11. CLR_CMOS1 (Jumper Block) 23 Motherboard Layout 1/2 ) ATX_L1/ATX_12V1 (24-pin/8-pin ATX power connectors) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to support the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. If you use a power supply that provides a 24-pin ATX power connector, please remove the small cover on the power connector on the motherboard before plugging in the power cord; otherwise, please do not remove it. 1 5 Pin No. Definition 1 GND 2 GND 3 GND 4 GND 5 P12V_CPU1 6 P12V_CPU1 7 P12V_CPU0 8 P12V_CPU0 4 8 24 12 1 13 Pin No. Definition Pin No. Definition 1 3.3V 13 3.3V 2 3.3V 14 -12V 3 GND 15 GND 4 +5V 16 PS_ON(soft On/Off) 5 GND 17 GND 6 +5V 18 GND 7 GND 19 GND 8 Power Good 20 -5V 9 5V SB(stand by +5V) 21 +5V 10 +12V 22 +5V 11 +12V(Only for 24-pin ATX) 23 +5V (Only for 24-pin ATX) 12 3.3V(Only for 24-pin ATX) 24 GND(Only for 24-pin ATX) 24 GS-R1233-RH Rack...