Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
6 Safety Information NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100. / for European users only / CAUTION • Danger of explosion if battery is incorrectly replaced. • Replace only with the same or equivalent type recommended by the manufacturer. • Dispose of used batteries according to the manufacturer’s instructions. 7 GS-R1161-RH Rack Mount Server Introduction Welcome to Gigabyte GS-R1161-RH Rack mount Server System Installation Guide. The guide provides instructions for configuration hardware for the GS-R1161-RH your system. This installation guide will assist you in installing all the essential components for the sever system. For your protection, please read and undertand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assume that your are a system or network administrator experienced in installing similar hardware. Contents Packages When opening the package, please ensure the system components are not damaged during the shipping. Using the following checklist to verify the contents. If any component is missing or damaged in the system, please contact your vendor immediately. • Chassis • GA-5YXS2-RH Motherboard (Installed) • Power Supply (Installed) • FAN Duct x 1 • CPU Heat Sink x 1 • Cables (RJ45) • Case Handle Kit x 2 • GS-R1161-RH Quick Refernece Guide • Driver CD for motherboard driver & utility * The items listed above are for reference only, and are subject to change without notice. 8 Feature Summary Motherboard ..GA-5YXS2-RH Chapter 1 Features Summary Processor Supported • Supports single Intel® Xeon® processor • Intel Xeon® Dual-Core/Quad-Core processor in LGA 775 socket • Supports 800/1066/1333MHz FSB Chipset • Intel® 3200 Chipset • Intel® ICH9R System Memory: Memory Capacity • 4 x DDR2 DIMM sockets up to 8GB Memory Type • Un-buffered 667/800 memory DIMM Size • Support 256MB, 512MB, 1GB, and 2GB memory Error Correction: • Single-bit Errors Correction, Multiple Bit Errors Detection Expansion Slot • 1 Riser card supports 1 PCI-E x8 and 1 PCI-E x8 (x1 bandwidth) add-on cards • 1 SO-DIMM add-on card SATA RAID controller Cooling Fans: • • • ICH9R Supports LSI Software SW RAID 0/1/10 (Windows only) 5 X System Fan Integrated LANs: Controller • Intel® 82566DC & 82573VGbE controllers Integrated Graphics: Controller • XGI Volari Z9s Graphics Memory • 32MB DDR2 Mass Storage System • 4 x Hot-Swap SATA HDDs Super I/O Controller • ITE IT8718F Super I/O Built-in I/O • 1 x Serial port (COM) • 4 x USB 2.0 dual-port connector (2 at front panel) • 1 x VGA connector • 2 x RJ45 LAN ports • P/S 2 Keyboard and Mouse Connectors System BIOS: BIOS Type • Phoenix BIOS on 8Mb flash ROM 9 GS-R1161-RH Rack Mount Server Server Management Functions: (Optional device) BMC Chip • H8S IPMI 2.0 controller Failure Detection • IPMI 2.0 specification of Server management Event Logging • 32KB Nonvolatile Memory to Log System Failure Events Remote Management • Follow the IPMI 2.0 specification of Server management Environment Ambient Temperature • Operating Temperature: 5oC to 40oC • Non-operating Temperature: 0oC to 50oC Relative Humidity • 10-80% operating Humidity at 30o C System Dimention: • 427.5mm x 567.5mm x 43.5 mm Electrical Power Supply • Single Power Supply 300W 10 11 Hardware Installation Process Please observe the safety information in chapter “Important Safety Information” Do not expose the server to extreme environmental conditions. Protect it from dust, humidity, and heat. Step 2-1: Chassis Removal and Installation Step 1 Push down the indentation located at two sides of the chassis. Step 2 Slide toward the top chassis cover. Step 3 Lift up to remove the top chassis cover. Step 4 Reverse Step 1, ,2, 3 to replace the chassis cover Chapter 2 System Hardware Installation 1 3 2 1 12 GS-R1161-RH Rack Mount Server Step 2-2: CPU Installation Please make sure the CPU type and speed that are supported by the motherboard. Step 1 Raise the metal locking lever on the socket. Insert the CPU with the correct orientation. Step 2 The CPU only fits in one orientation. Step 3 Push the metal lever back into locked position. 1 2 3 13 Hardware Installation Process Step 2-3: Heat Sink Installation Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well remember to apply the thermal conductivity compound on the CPU. Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed. 1 2 2 2 2 GS-R1161-RH Rack Mount Server Step 2-4: Memory Installation Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down. Step 2. Close the plastic clip at both...