Оценок - 5, средний балл: 3.6
(
)
)
|
К этому устройству также есть другие инструкции:
Материнские платы - A8N-SLI (2.57 mb)
Материнские платы - A8N-SLI (87.6 kb)
Материнские платы - A8N-SLI (4.17 mb)
Фрагмент инструкции
14. 14.14.14.14.14. Coaxial S/PDIF Out port. Coaxial S/PDIF Out port.Coaxial S/PDIF Out port.Coaxial S/PDIF Out port.Coaxial S/PDIF Out port.Coaxial S/PDIF Out port. This port connects an external audio output device via a coaxial S/PDIF cable. 15. 15.15.15.15.15. PS/2 keyboard port (purple). PS/2 keyboard port (purple).PS/2 keyboard port (purple).PS/2 keyboard port (purple).PS/2 keyboard port (purple).PS/2 keyboard port (purple). This port is for a PS/2 keyboard. ASUS A8N-SLI ASUS A8N-SLIASUS A8N-SLIASUS A8N-SLIASUS A8N-SLIASUS A8N-SLI1-19 1-191-191-191-191-19 1.7.2 1.7.21.7.21.7.21.7.21.7.2 Internal connectors Internal connectorsInternal connectorsInternal connectorsInternal connectorsInternal connectors 1. 1.1.1.1.1.Floppy disk drive connector (34-1 pin FLOPPY) Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. The Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. 2. 2.2.2.2.2.Serial port connector (10-1 pin COM1) Serial port connector (10-1 pin COM1)Serial port connector (10-1 pin COM1)Serial port connector (10-1 pin COM1)Serial port connector (10-1 pin COM1)Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. A8N-SLI ® PIN 1 A8N-SLI Floppy disk drive connector A8N-SLI ® A8N-SLI COM port connector COM1 PIN 1 Chapter 1: Hardware information Chapter 1: Hardware informationChapter 1: Hardware informationChapter 1: Hardware informationChapter 1: Hardware informationChapter 1: Hardware information 3. 3.3.3.3.3.IDE connectors (40-1 pin PRI_IDE, SEC_IDE) IDE connectors (40-1 pin PRI_IDE, SEC_IDE)IDE connectors (40-1 pin PRI_IDE, SEC_IDE)IDE connectors (40-1 pin PRI_IDE, SEC_IDE)IDE connectors (40-1 pin PRI_IDE, SEC_IDE)IDE connectors (40-1 pin PRI_IDE, SEC_IDE) These connectors are for Ultra DMA 133/100/66 signal cables. The Ultra DMA 133/100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/ 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. • The Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for UltraDMA133/100/66 IDE devices. A8N-SLI ® A8N-SLI IDE connectors SEC_IDE PRI_IDE NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PIN 1 ASUS A8N-SLI ASUS A8N-SLIASUS A8N-SLIASUS A8N-SLIASUS A8N-SLIASUS A8N-SLI1-21 1-211-211-211-211-21 4. 4.4.4.4.4. Serial ATA connectors Serial ATA connectorsSerial ATA connectorsSerial ATA connectorsSerial ATA connectorsSerial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) (7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4)(7-pin SATA1, SATA2, SATA3, SATA4) Supported by the NVIDIA® nForce™4 SLI chipset, these connectors are for the Serial ATA signal cables for Serial ATA hard disk drives that allow up to 3Gb/s of data transfer rate. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, or RAID 1+0 configuration that span across the Parallel ATA drives. These connectors are set to SATA SATASATASATASATA SATA by default. In SATA mode, you can connect Serial ATA boot or data hard disk drives to these connectors. If you intend to create a Serial ATA RAID set using these connectors, enable the RAID function of each port from the NVRAID NVRAIDNVRAIDNVRAIDNVRAIDNVRAID Configuration ConfigurationConfigurationConfigurationConfigurationConfiguration sub-menu item in the BIOS. See section “2.4.3 Onboard Devices Configuration” on pages 2-24 and 2-26 for details. A8N-SLI ® A8N-SLI SATA connectors GNDRSATA_RXN4 RSATA_RXP4 GNDRSATA_TXN4 RSATA_TXP4 GND GNDRSATA_RXN3 RSATA_RXP3 GNDRSATA_TXN3 RSATA_TXP3 GND SATA4 SATA3 GNDRSATA_RXN2 RSATA_RXP2 GNDRSATA_TXN2 RSATA_TXP2 GND GNDRSATA_RXN1 RSATA_RXP1 GNDRSATA_TXN1 RSATA_TXP1 GND SATA2 SATA1 The actual data transfer rate depends on the speed of Serial ATA hard disks installed. Serial ATA Master/Slave connectors Serial ATA Mast...