Оценок - 4, средний балл: 4.5 ( )

Производитель: Antec Размер: 667.94 kb Название файла: SLK1650_Manual_fr.pdf Язык инструкции:

6. Find a small 4-pin connector on the power supply and connect it to the male 4-pin connector on the floppy drive. 7. Connect a 4-pin large connector from the power supply to the male 4-connector on each of the other devices. Installing 5.25" Devices 1. If you look into the 5.25" drive bays from above the power see some metal grilles covering the front of those bays. Carefully screwdriver through the metal grille, and gently remove bay cover by pushing outwards. 3 2. Use your hands to twist the metal plate back and forth until it breaks off. Note: Don't break off the metal grilles covering the drive bays that you don't intend to use now. Be careful of the newly exposed metal where the grille was attached, as these areas are likely to be sharp. 3. Using the screws provided, fasten your 5.25" device into the drive bay. 4. Repeat the same procedure for other devices. 5. Connect a 4-pin large connector from the power supply to the male 4-pin connector on each of the devices. Connecting the Data Cables After you've connected the devices to the power supply, you need to connect data cables between the devices and the motherboard. To achieve the best data-transfer and cooling performance, we recommend using premium rounded cables such as Antec Cobra Cables. The cables that are included with your drives should have a red strip on one side indicating pin number 1. If you use these cables, make sure that the red strip is on pin 1, usually toward the power connector. Installing the Fan We've included one rear-mounted 120mm exhaust fan. In the front of the case, you'll also find a mount for an optional 80mm intake fan. The rear fan is installed so that the air blows out of the case. Find a large 4-pin peripheral connector on the power supply and connect it to the male 4-pin connector on the fan. The front fan (optional) should be installed so that the air is blowing into the case from the front. To mount the optional front fan: 1. Squeeze the upper right and left sides of the fan cage together to release the tabs. Once the cage is loose, slide it upwards. You should then be able to pull the cage back and out of the case. 2. Drop the fan into the cage from the case's front side, and push it in until the four tabs snap the fan in place. We recommend routing the fan's power wires through any of the slots near each corner of the fan cage. (Make sure you don't pinch the wires.) No screws are needed. The front fan should be installed so that the air is blowing into the case. 3. Reattach the cage/fan assembly to the case, taking care not to pinch the fan wires. 4. Connect a large 4-pin connector from the power supply to the male 4-pin connector on each of the fans. Chassis Air Guide Your new case includes a chassis air guide, which provides cooling to the CPU. The air guide consists of three parts: an upper duct, lower duct. If you prefer, you can adjust the distance between and your CPU for maximum cooling efficiency. 4 SLK1650_Manual_intl.qxd 5/14/2004 3:49 PM Page 10 You could also install an 80mm intake fan between the air guide and the case's side panel. This will further improve your system's cooling airflow. To mount the optional fan between the chassis air guide and the side panel: 1. Remove the chassis air guide from the side panel. 2. Attach the fan to the side panel (see Figure 1). 3. Using the fan screws, lock the flange of the air guide to the fan (see Figure 2). 4. Connect a large 4-pin peripheral connector from the power supply to the male 4-pin connector on the fan. Figure 1 Figure 2 Antec Quality 3-Year parts and labor warranty (AQ3) See details at: 5 6 SLK1650_Manual_intl.qxd 5/14/2004 3:49 PM Page 12 Chez Antec, nous ameliorons constamment nos produits pour garantir la plus haute qualite. Il est donc possible que votre nouveau boitier differe legerement des descriptions fournies dans ce manuel. Ceci n'est pas un probleme, seulement une amelioration. A la mise sous presse, toutes les caracteristiques, descriptions et illustrations de ce manuel sont correctes. Avis de non-responsabilite Ce manuel est un guide de reference Antec. Pour des instructions detaillees d'installation de la carte mere et des peripheriques, reportez-vous au guide fourni avec vos composants et unites de disque. SLK1650 & SLK1650B – Boitier Mini Tour Alimentation Le nouveau boitier est equipe d'un bloc d'alimentation SmartPower ultra silencieux de 350 Watts muni d'un interrupteur de marche/arret. Assurez-vous de mettre l'interrupteur en position ON (I) avant de demarrer l'ordinateur pour la premiere fois. En regle generale, il est inutile de mettre l'interrupteur en position OFF (O) etant donne que le bloc d'alimentation inclut une fonctionnalite logicielle de marche/arret. Grace a l'interrupteur logiciel du boitier de l'ordinateur, vous pouvez mettre l'ordinateur sous et hors tension. Si l'ordinateur plante et que vous ne parvenez pas a l'arreter a l'aide de l'interrupteur logiciel, vous pouvez mettre...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: