Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
As such, your new product may differ slightly from the description in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to the user manuals that come with those components and drives. MINUET 350 USER’S MANUAL The Minuet 350 is a small case that’s big on features. It can be configured in a desktop or vertical orientation. It comes with an 80PLUS® certified 350 Watt power supply (PSU). The PSU generates less heat because it is designed for high efficiency. This keeps the power supply cool and prolongs its working life. The PSU includes Universal Input with Active Power Factor Correction (PFC). Universal Input allows you to connect your PSU to any AC power outlet between 100~240V without setting a voltage switch. Active PFC reduces electrical waste by improving the power factor value to the power supply, helping the power plant to provide power more efficiently. The PSU comes with an on/off switch. Make sure you turn the switch to the ON (I) position before you boot up your computer for the first time. Normally, you won’t need to switch it OFF (O), since the power supply can be controlled with the soft on/off switch on the front of your computer case. If your computer crashes and you can’t shut it down using the soft switch, you can switch the main power to the OFF (O) position to clear the fault, then reboot. SETTING UP 1. Take the case out of the box. Remove the Styrofoam and the plastic bag. Place the case on a flat surface. 2. Remove the thumbscrews from the top panel (at the rear of the case). Slide the panel to the rear of the case and remove it. Set the panel safely aside. Note: Please don’t try to use your fingernails to pry or lift the panel. 3. Inside the case you should see the power supply, some wiring with marked connectors (USB, PWR etc.), an installed I/O panel and a power cord. You will also find a bag of screws, four rubber feet and two plastic stands. 4. Horizontal Orientation: stick the four adhesive rubber feet to the bottom panel of the case to protect the paint from scratches. 5. Vertical Orientation: place the Minuet 350 in the two plastic stands such that the side panel with the 80mm fan is facing up. Adjust the stands to fit snugly against the case sides. 1 Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend taking the appropriate time and caution when working with it. Please take reasonable precautions. MOTHERBOARD INSTALLATION This manual does not cover CPU, RAM, or expansion card installation. Please consult your motherboard manual for specific mounting instructions and troubleshooting. 1. Lay the case down so that the open side is up. You should be able to see the drive cage and power supply. 2. Make sure you have the appropriate I/O panel for the motherboard. If the panel provided is not suitable for the motherboard, please contact the motherboard manufacturer for the correct I/O panel. 3. Line up the motherboard with the standoff holes. Determine which holes line up and remember where they are. Not all motherboards will match with all of the provided screw holes, and this is not necessary for proper functionality. Some standoffs may be pre-installed for your convenience. 4. Remove the motherboard by lifting it up. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the motherboard on the standoffs. 7. Screw in the motherboard to the standoffs with the provided Phillips-head screws. 8. The motherboard is now installed. POWER/LED CONNECTIONS The power supply is an ATX12V form factor power supply. It has a single 24-pin Main Power Connector, and a 4-pin +12V Power Connector for the motherboard. It is backwards compatible to previous ATX form factor power supplies. If your motherboard does not support the +12V 4-pin Power Connector, you can still use this power supply. It also comes with three 4-pin Peripheral Power Connectors, one SATA Power Connector and one 4-pin Floppy Drive Power Connector for your drives. 1. Connect the 24-pin Main Power Connector and Picture 1 Picture 2 the 4-pin 12V connector to the motherboard as needed. If the motherboard uses a 20-pin connector, detach the 4-pin attachment on the 24-pin power connector (see pictures 1 and 2). For 24-pin For 20-pin Note: the detachable 4-pin section cannot be motherboards motherboards used in place of a 4-pin +12V connector. 2. Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard. Polarity (positive and negative) does not matter for switches. 3. Connect the Power LED (labeled POWER LED) to your motherboard. For LEDs, colored wires are positive (+). White or black wires are negative (–). If the LED does not light up wh...