Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance would void the compliance to FCC regulations and therefore, the user’s authority to operate the equipment. Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. iii AIMB-258 User Manual Technical Support If a problem arises with your system and no solution can be obtained from the user.s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance. Visit the Advantech website for FAQ, technical guide, BIOS updates, driver updates, and other information: Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: • 1 x AIMB-258 Intel® µFC-PGA 478 Core 2 Duo Mini ITX Motherboard • 2 x SATA HDD cable • 2 x SATA Power cable • 1 x Serial port cable 1 to 4 • 1 x I/O port bracket • 1 x Startup manual • 1 x Driver CD • 1 x Warranty card If any of the above items is damaged or missing, please contact your retailer. AIMB-258 User Manual iv Contents Chapter 1 Product Introduction ...........................1 1.1 Before You Proceed..................................................................................2 1.2 Motherboard Overview..............................................................................2 1.2.1 Placement Direction......................................................................2 1.2.2 Screw Holes..................................................................................3 1.3 Motherboard Layout .................................................................................. 4 Figure 1.1 Motherboard Layout ................................................... 4 1.4 Specifications ............................................................................................ 5 1.5 Operating System support list ................................................................... 6 1.6 Board Diagram .......................................................................................... 7 1.7 Ordering Information ................................................................................. 8 1.8 Riser Card.................................................................................................8 1.9 Bracket View ............................................................................................. 8 1.10 Accessories...............................................................................................8 1.11 Layout Content List ................................................................................... 9 Table 1.1: Jumper Setting List.....................................................9 Table 1.2: JSETCOM1: COM1/+5 V/+12 V Selection ................. 9 Table 1.3: JSETCOM2: COM2 RS232/422/485 Mode Selection 9 Table 1.4: CMOS1: Clear CMOS .............................................. 10 Table 1.5: J1:LCD Power 3.3 V/5.5 V Selection........................10 Table 1.6: PSON1: ATX, AT Mode Selection ............................ 10 Table 1.7: JWDT1: Watchdog Timer Output Option..................11 Table 1.8: JOBS: HW monitor ................................................... 11 1.12 Central Processing Unit (CPU) for AIMB-258 ......................................... 11 1.12.1 Installing the CPU ....................................................................... 12 1.12.2 Installing the CPU Heatsink and Fan..........................................14 1.12.3 Uninstalling the CPU Heatsink and Fan...................................... 16 1.13 System Memory ...................................................................................... 17 1.13.1 DIMM Sockets Location..............................................................17 1.13.2 System Memory..........................................................................17 1.13.3 Memory Support List...................................................................18 Table 1.9: SODIMM DDR3........................................................18 1.14 Connectors......................................................