Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note: When the Computer lock switch is in the locked position, the Eject lever cannot be operated. NOTE ❖ Certain USB devices, such as optical disc drives and hard disk drives, have high power requirements. Due to the power output limitations of the USB ports, you may not be able to operate more than one such device at a time. ❖ If your USB device came with an AC adaptor, be sure to connect the device to a power outlet with the AC adaptor, in addition to connecting the device to the port replicator with a USB cable. ❖ Booting from a USB 3.0 port is only available if your computer supports it. ❖ The speed of the USB 3.0 port on the port replicator is dependent on your computer’s specifications. Special features The port replicator supports the following power-saving features, if they are available on your computer. Refer to your computer documentation for details. Feature Purpose Wake On LAN Wake Up (USB) When a computer in sleep or hibernation mode is connected to the port replicator, this feature turns on the computer when a wake-up signal is received from a connected LAN cable. When a computer in sleep or hibernation mode is connected to the port replicator, this feature turns on the computer when a wake-up signal is received from a device connected to a USB port. Note: When the Wake Up (USB) feature is enabled and the docked computer is in sleep or hibernation mode, the computer’s AC power light may be ON or OFF, depending on the computer model. In either case, the computer will turn on when a wake-up signal is received from a USB device. Setting up the port rep licator 13 Setting up the port replicator To set up the port replicator, follow the steps below: 1 Turn off your computer. 2 Disconnect all cables/cords from your computer. 3 Connect your external devices to the appropriate ports on the port replicator. 4 Connect the included AC adaptor to the port replicator. A The supplied power cord conforms to safety rules and regulations in the region where the product was purchased. Do not use the AC adaptor that was included with your computer. Always use the Toshiba AC adaptor that was provided with this product or use Toshiba recommended alternate adaptors to avoid any risk of fire and/or other damage to the computer and/or port replicator. Use of an incompatible AC adaptor could cause fire and/or damage to the computer and/or port replicator, possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. a When you connect the AC adaptor to the port replicator, always follow the steps in the exact order as described below. Connecting the power cable to a live electrical outlet should be the last step, otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts. (Sample Illustration) Connecting the power cord to the AC adaptor a Connect the provided power cord to the AC adaptor. b Connect the AC adaptor to the DC-IN connector that came with your Hi-Speed Port Replicator. 14 Docking your computer replicator c Connect the power cord plug to a live electrical outlet. The port replicator is now ready for use. See “Docking your computer” below to learn how to connect your computer to the port replicator. Docking your computer The system supports hot docking and undocking. To dock your computer to the port replicator, follow the steps below: 1 Align the slots on the bottom of your computer (near the hinge at the back of the computer) with the guide pins on the port replicator. Lower the computer onto the port replicator. (Sample Illustration) Aligning your computer with the port replicator Docking your computer 15 2 Press down on the back of the computer until it clicks into place. The computer connector on the port replicator engages the computer’s expansion port. When the computer is connected, the docking indicator light glows green. (Sample Illustration) Connecting a computer to the port replicator 3 If the computer is not already on, press the power button on the port replicator to turn the computer on. The power light on the computer will turn on, indicating that the computer is receiving power. If the computer does not turn on, please see “Troubleshooting” on page 20. NOTE The first time you dock your computer, a message should appear on your computer screen indicating the devices connected to the port replicator are ready to use. NOTE You can leave your computer docked in the port replicator overnight. Use the standard Windows® shutdown procedure, which will automatically power off your computer. Press the power button on the port replicator (or the computer's power button) when you are ready to turn the computer on again. 16 Undocking your computer Undocking your computer The system supports hot docking and undocking. I caution I Do not disconnect the computer f...
Эта инструкция также подходит к моделям:Компьютерные аксессуары - PA3838U-1PRP (1.85 mb)