Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The AD9272/AD9273 data sheet, available at provides additional information and should be consulted when using the evaluation board. All documents and software tools are available at For any questions, send an email to highspeed.converters@analog.com. TYPICAL MEASUREMENT SETUP Adobe Systems 07782- 001 Figure 1. AD9272-65EBZ/AD9272-80KITZ/AD9273-50EBZ Evaluation Board and HSC-ADC-EVALCZ Data Capture Board TABLE OF CONTENTS Features .............................................................................................. 1 Equipment Needed ........................................................................... 1 Documents Needed .......................................................................... 1 Software Needed ............................................................................... 1 General Description ......................................................................... 1 Typical Measurement Setup ............................................................ 1 Revision History ............................................................................... 2 Evaluation Board Hardware ............................................................ 3 Power Supplies .............................................................................. 3 Input Signals .................................................................................. 3 Output Signals ............................................................................... 3 Default Operation and Jumper Selection Settings ....................5 Evaluation Board Software Quick Start Procedures .....................7 Configuring the Board .................................................................7 Using the Software for Testing .....................................................7 Using the Integrated Crosspoint Switch (CW Doppler Mode) ................................................................. 10 Evaluation Board Schematics and Artwork ................................ 12 Ordering Information .................................................................... 23 Bill of Materials ........................................................................... 23 ESD Caution .................................................................................... 24 REVISION HISTORY 2/09—Revision 0: Initial Version EVALUATION BOARD HARDWARE The AD9272/AD9273 evaluation board provides all of the support circuitry required to operate the AD9272/AD9273 in its various modes and configurations. Figure 2 shows the typical bench characterization setup used to evaluate the ac performance of the AD9272/AD9273. It is critical that the signal sources used for the analog input and clock have very low phase noise (<1 ps rms jitter) to realize the optimum performance of the signal chain. Proper filtering of the analog input signal to remove harmonics and lower the integrated or broadband noise at the input is necessary to achieve the specified noise performance (see the AD9272 or AD9273 data sheet). See the Evaluation Board Software Quick Start Procedures section to get started and Figure 21 to Figure 31 for the complete sche- matics and layout diagrams that demonstrate the routing and grounding techniques that should be applied at the system level. POWER SUPPLIES This evaluation board comes with a wall-mountable switching power supply that provides a 6 V, 2 A maximum output. Connect the supply to the rated 100 V ac to 240 V ac wall outlet at 47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter jack that connects to the PCB at P701. Once on the PC board, the 6 V supply is fused and conditioned before connecting to low dropout linear regulators that supply the proper bias to each of the various sections on the board. When operating the evaluation board in a nondefault condition, L705, L706, L707, and L709 can be removed to disconnect the switching power supply. This enables the user to bias each section of the board individually. Use P602 and P603 to connect a different supply for each section. At least one 1.8 V supply is needed with a 1 A current capability for AVDD_DUT and DRVDD_DUT; however, it is recommended that separate supplies be used for both analog and digital domains. An additional supply is also required to supply 3.0 V to the device under test, AVDD2_DUT. This should also have a 1A current capability. To operate the evaluation board using the SPI and alternate clock options, a separate 3.3 V analog supply is needed in addition to the other supplies. The 3.3 V supply, or AVDD_3P3V, should have a 1 A current capability. To bias the crosspoint switch circuitry or CW section and differential gain drive circuitry, separate +5 V and .5 V supplies are required at P601. These should each have 1 A current capability. This section cannot be biased from a 6 V, 2 A wall supply. Separate supplies are required at P601. INPUT SIGNALS When connecting the clock and analog source, use clean si...
Эта инструкция также подходит к моделям:Компьютерные аксессуары - UG-001 (2.38 mb)
Компьютерные аксессуары - AD9272 (2.38 mb)