tea and coffee carry a 90 day warranty; and, decanters are excluded. THIS WARRANTY IS THE COMPLETE AND ONLY WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN FACT, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND/OR INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH BLOOMFIELD PRODUCTS. This warranty is void if it is determined upon inspection by an Authorized Service Agency that the equipment has been modified, misused, misapplied, improperly i

2 Water Supply Installation INSTALLATION (continued) INSTALLATION (continued) WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brewer or result in decreased performance. Such damage is not covered by warranty. IMPORTANT: Do not conne

Failure to do so will result in movement of the brewer which can cause personal Injury and/ or damage to brewer. WARNING ELECTRIC SHOCK HAZARD: Brewer must be plugged into a properly grounded electrical receptacle to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Ve

To reset press and hold CANCEL for 3 seconds, or re-energize the brewer. (Possible causes of the problem are: no incoming water; slow flow of incoming water, sensor not reading, etc.). E. Keyswitch Locked: If a key switch is depressed for 10 seconds this error message will occur. Lights will flash alternately and the brewer will turn off all valves and elements. Press and hold the CANCEL key for 3 seconds to reset the brewer (or re-energize the brewer). If the problem re-occurs this indicates a

Fig. 11 Adjust Solenoid Time IMPORTANT: Before setting assembly into tank, make sure tank lid gasket is properly seated on flange of lid. IMPORTANT: When mounting thermostat, be sure a new seal washer is placed below the fitting on the capillary line. Push sensing bulb thru tank lid until fitting seats. Tighten capillary lock nut only enough to ensure no water leakage. Excessive tightening is not necessary. 13 SERVICING INSTRUCTIONS (continued) REPLACE HEATING ELEMENT Remove tank cover assembly

Data, specifications and materials, and model number designations are subject to change at any time without notice. This manual is intended for use by qualified service personnel. Bloomfield coffee brewers are intended exclusively for commercial use and are designed expressly to brew beverage products for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Except as noted, this piece of equipment is made in the USA and has American sizes on hardware. A

CLAMP 1 35 BRACKET, WATER OUTLET VALVE 1 36 85018 DECAL, KEYPAD OVERLAY 1 37 83745 7/16-20 FEM x 7/16-20 MALE 1 39 8552-18 TERMINAL BLOCK 240V 1 40 8043-11 ELBOW, VENT 1 41 83763 82936 SWITCH 120V SWITCH, ROCKER ON-OFF 240V 1 ITEM PART # DESCRIPTION QT 42 66385 9012-38 FITTING, CONDUIT 3/4" STR 240V STRAIN RELIEF LIQ. TIGHT 120V 1 43 63046 PLUG, HOLE 1" 120V 1 45 8033-56 CAP LEVELER 4 46 8033-55 LEG LEVELER PLATED 4 48 83571 INSERT, SPRAY HEAD 1 50 83810 BRACKET POSITIONING 1 51 63201 SPACER 4 C

6. The unit will revert to the energy-saver mode some time after the last brew, based on AFTER HOURS TIME setting. WARNING: RISK OF INJURY The following servicing sections are for operator reference only. All servicing and/or repairs must be performed by a qualified technician Reset Hi-Limit Thermostat 240 V & Dual Voltage Units 14 SERVICING INSTRUCTIONS - ELECTRICAL FUNCTION 1. Pressing the POWER key energizes the unit. The POWER LED will glow whenever the unit is ON. 2. Automatic fill is accom

CLAMP 1 35 BRACKET, WATER OUTLET VALVE 1 36 85018 DECAL, KEYPAD OVERLAY 1 37 83745 7/16-20 FEM x 7/16-20 MALE 1 39 8552-18 TERMINAL BLOCK 240V 1 40 83571 INSERT, SPRAYHEAD 1 41 83763 82936 SWITCH 120V SWITCH, ROCKER ON-OFF 240V 1 ITEM PART # DESCRIPTION QT 42 66385 9012-38 FITTING, CONDUIT 3/4" STR 240V STRAIN RELIEF LIQ. TIGHT 120V 1 43 63046 PLUG, HOLE 1" 120V 1 45 8033-56 CAP LEVELER 4 46 8033-55 LEG LEVELER PLATED 4 48 83571 INSERT, SPRAY HEAD 1 50 83810 BRACKET POSITIONING 1 51 63201 SPACER