Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
8). • Turn the Selector Control to ‘STEAM’ and allow the appliance to produce steam for 4-5 seconds to clear the steam tube. The filter holder does not have to be locked into position. • Turn the Selector Control to ‘STANDBY’, switch off at the power outlet, remove the plug and allow the appliance to cool. • Remove all steam pressure by following the instructions on Page 10. • After the steam pressure has been released, remove the water tank cap and discard the remaining water (always empty the water tank between uses). • The steam nozzle must be screwed back onto the steam tube in a clockwise direction and tightened using reasonable force with the end of the cleaning tool provided. and drip tray can be washed with soapy water.The drip tray consists of 2 parts and can be removed for easier cleaning. (Fig. 6). Fig. 6 Fig. 8 Fig. 7 NOTE: Do not place any of the components in the dishwasher. Decalcifying Hard water can cause limestone build up in and on the inner functioning components, reducing the brewing flow, power of the appliance, and affecting the quality of coffee. We advise decalcifying the appliance on a regular basis (once a month) using a liquid decalcifying agent. Follow the instructions provided or use the following as a guide: Diluted solution (for softer water) • 1 part decalcifying agent • 2 parts cold tap water Concentrated solution (for harder water) • 1 part decalcifying agent • 1 part cold tap water Decalcifying the appliance • Ensure the Selector Control is in the ‘STANDBY’ position, the appliance is switched off at the power outlet and that the plug is disconnected. • Ensure the appliance is cool and all steam pressure in the appliance has been released. • Remove the stainless steel filter from the filter holder and place the filter holder back in position. • Place an empty cup on the drip tray, under the filter holder. • Remove the water tank cap and pour in the decalcifying solution. • Screw the water tank cap back on (make sure the cap is on tight). • Plug the appliance into the power outlet and turn the power switch on. • Turn the Selector Control to the ‘BREW’ position and allow the decalcifying solution to run through the filter holder. • When the solution has run through the appliance (make sure that all the solution has run out and there is no steam pressure in the appliance), turn the Selector Control to the ‘STANDBY’ position, switch off at the power outlet and remove the plug and allow the appliance to cool. • After decalcifying, rinse the water tank thoroughly and refill with cold tap water. • Repeat the above procedures several times by running clear the water through the filter holder and through the steam nozzle (half each).This should remove any possible residual after taste left by decalcifying agent. • Replace the stainless steel filter and the appliance is ready to use. NOTE: The stainless steel filters should not come in contact with any decalcifying agents. Do not use powdered decalcifying agents. WARNING: To avoid possible burns from hot steam and water, never open the water tank cap while there is pressure in the water tank. Remove all pressure first. Troubleshooting Trouble Shooting Chart Problem Causes Coffee does not • Appliance was not switched on or plugged in. come out through the filter holder • No water in tank. • Selector control not in ‘Brew’ position. • Coffee grind is too fine. • Too much coffee in the filter. • Water tank cap is not secure, steam is escaping. Coffee comes out too quickly • Coffee grind is too coarse. • Not enough coffee in filter. Coffee is too weak or watery • Coffee grind is not fine enough - use Espresso ground coffee. Coffee comes • Filter holder is not inserted in the brew head. out around the filter holder • There are coffee grounds around the filter holder rim. • There is too much coffee in the filter. • Coffee has been packed too tightly. No steam is generated • Appliance is not turned on. • The water tank is empty. • There is too much water in the water tank, (no room for steam). • Selector control not in ‘Steam’ position. Coffee is splattering out of the filter holder • The water tank is empty or low (not enough pressure). Milk not foamy after frothing • Not enough steam. • Ensure milk selected is suitable for frothing Notes Notes 18 Notes Kambrook 12 Month Replacement Warranty Kambrook 12 Month Replacement Warranty In Australia, this Kambrook Replacement Warranty does not affect the mandatory statutory rights implied under the Trade Practices Act 1974 and other similar State and Territory legislation relating to the appliance. It applies in addition to the conditions and warranties implied by that legislation. In New Zealand, this Kambrook Replacement Warranty does not affect your mandatory statutory rights implied under the Consumer Guarantees Act 1993 in relation to the appliance. It applies in addition to the conditions and guarantees implied by that legislation. This Kambrook Replacement Warranty is valid only in the cou...