Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
degrees to the left (Fig 2 ). fig 2 • Place the filter retainer clip in the release position by pulling the clip back towards your hand. • Place the filter holder underneath the brew head so that the handle is positioned to the left of centre. Lift the filter holder until it contacts the brew head and rotate to the right. • Place the 2 or 4 cup filter into the filter holder and use the measuring spoon to fill the filter with ground espresso coffee to the required cup level marking inside the filter (use the smaller filter for 1 or 2 cups and the larger filter for 2 or 4 cups). Do not fill above the 2 or 4 cup mark. fig 3 fig 4 correct (level) Incorrect (Heaped) • Distribute the ground coffee evenly and press it lightly with the measuring spoon (Fig 3 and 4). Too much coffee can block the flow of water. THE METAL PARTS OF THE FILTER HOLDER MIGHT STILL BE VERY HOT. COOL DOWN THESE PARTS BY RUNNING UNDER COLD WATER. TO AVOID POSSIBLE BURNS FROM HOT STEAM AND WATER, NEVER OPEN THE WATER TANK CAP WHILE THERE IS PRESSURE IN THE WATER TANK. REMOVE ALL PRESSURE FIRST. NEVER LET COFFEE OR WATER LEVEL IN A CUP REACH THE POURING NOZZLE OF THE FILTER HOLDER. BREWING THE COFFEE The twin nozzle filter holder allows you to make either one or two espresso coffees at a time. • Make sure the drip tray is in place. Place empty coffee cups on the drip tray under the filter holder. • Make sure the Brew/Steam Selector Control is in the ‘STANDBY’ position. • Plug the power cord into a 230/240v power outlet and switch on. • The red power ‘On’ light will illuminate when the appliance has been switched on at the power outlet and the cup warming plate will start heating. • Rotate the Selector Control to the ‘BREW’ position . The orange heating light will illuminate to let you know the water is heating. Coffee will begin to flow into the cups in approximately five minutes. • The Pressure Indicator Button on the Water Tank Cap will rise when sufficient steam pressure is achieved. • When sufficient coffee has flowed into the cups, turn the Selector Control back to the ‘STANDBY’ position. This will stop the flow of coffee. • If you are not continuing to using the steam function, switch off at the power outlet, unplug the power cord, remove all pressure and allow the appliance to cool. • Do not remove the water tank cap or filter holder until the steam pressure in the appliance has been released. The Pressure Indicator Button should drop down and be flush with the top of the water tank cap. The steam pressure in the machine must be released each time BEFORE re-filling with fresh cold water. 9 OPERATING YOUR BREVILLE CAPPUCCINO MAKER OPERATING YOUR BREVILLE CAPPUCCINO MAKER OPERATING YOUR BREVILLE CAPPUCCINO MAKER OPERATING YOUR BREVILLE CAPPUCCINO MAKER HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTE A cappuccino is an espresso topped with steamed and frothed milk ( 1. 3 espresso, 1. 3 steamed milk, 1. 3 frothed milk), traditionally served luke warm in a cup. A latte is an espresso topped with steamed and frothed milk ( 1. 3 espresso, topped with steamed milk and about 10cm of frothed milk), traditionally served in a glass wrapped with a serviette. • The first step in making a cappuccino/latte is to make a short espresso (Follow steps in ‘How to make an Espresso’). • Fill the frothing jug 1/3 full with cold milk (skim milk is the easiest to froth). • Hold the frothing jug below the froth enhancer. Immerse the froth enhancer 10mm into the milk and rotate the Selector Control to the ‘STEAM’ position . Gently move the frothing jug in a circular motion around the froth enhancer. • When the milk begins to increase in volume, immerse the froth enhancer deeper into the milk to further heat the milk. Do not allow the milk to boil. • Turn the Selector Control to the ‘STANDBY’ position to stop the steaming function before removing the jug. • Add the steamed milk to each cup of freshly brewed espresso coffee and spoon on the frothed milk. • Switch the power off at the power outlet, unplug the power cord, remove all steam pressure and allow the appliance to cool. • Do not remove the water tank cap or the filter holder until the steam pressure in the appliance has been released. The Pressure Indicator Button should drop down and be flush with the top of the water tank cap. 10 TO AVOID SPLATTERING OF HOT MILK, DO NOT LIFT THE STEAMING NOZZLE ABOVE THE SURFACE OF THE MILK WHILE FROTHING. ENSURE THE SELECTOR CONTROL IS IN THE ‘STANDBY’ POSITION BEFORE REMOVING THE FROTHING JUG. HOW TO RELEASE THE STEAM PRESSURE • Switch the power off at the power outlet and unplug the power cord. • Place the frothing jug under the steam pressure fig 5 nozzle. indicator down • Turn the selector control to the ‘STEAM’ position and allow all steam and • After the steam pressure has been residual water to completely drain off into released, remove the filter holder from the the jug until all flow and sound ceases. brew head. Using the filter retainer clip to The steam pressure i...