Оценок - , средний балл: ( )

Инструкция по эксплуатации Philips, модель 10001894

Производитель: Philips
Размер: 1.84 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Wait until there is a steady jet of steam. • Close the knob (3) and remove the container. • Fill a container 1/3 with cold milk. Use cold milk to get a better froth. • (Fig.20) - Immerse the steam spout in the milk and open the knob (3) by turning it counter-clockwise. Turn the milk container with slow upward movements so that it is warmed evenly. • Once the container is filled with milk froth, close the knob (3), remove the cup with the frothed milk. • (Fig.19) - Press the steam button (16) again. • Proceed with circuit priming as described in section 4.5 to make the machine ready for use. Note: The machine is ready when the machine ready light (15) is permanently on. Note: If it is not possible to dispense steam as described, prime the circuit as explained in section 4.5 and then repeat the steps. The same process can be used to heat other beverages. • After this operation, clean the steam spout with a wet cloth. 9 CLEANING Maintenance and cleaning may only be carried out when the machine has cooled down and has been disconnected from the power supply. • Do not immerse the machine in water or place any of its parts in a dishwasher. • Do not use alcohol, solvents and/or aggressive chemical agents. • We recommend cleaning the water tank and filling it up with fresh water daily. • (Fig.21-22) - Every day, after heating the milk, remove the external part of the Pannarello and wash it with fresh drinking water. • (Fig.23) - The steam spout should be cleaned weekly. In order to do this, you need to: - Remove the external part of the Pannarello (for standard cleaning); - Loosen the ring nut (without removing it); - Remove the upper part of the Pannarello from the steam spout; - Wash the upper part of the Pannarello with fresh drinking water; - Wash the steam spout with a wet cloth and remove any milk residue; - Replace the upper part of the steam spout (make sure it is completely inserted); - Tighten the previously loosened ring nut. - Reassemble the external part of the Pannarello. • (Fig.24) - Empty and clean the drip tray daily. • Use a damp cloth to clean the appliance. • (Fig.17) - To clean the Portafilter proceed as follows: - Remove the filter, wash it thoroughly with hot water. - Remove the adapter (if fitted), wash it thoroughly with hot water. - Wash the internal part of the Portafilter. • Do not dry the machine and/or its components using a microwave and/or conventional oven. 10 Descaling Limescale builds up with the use of the appliance; the machine needs descaling every 1-2 months and/or whenever a reduction in water flow is noticed. Use the Saeco descaling product. Its formula has been designed to ensure better machine performance and operation for its whole operating life. If correctly used, it also avoids alterations in the brewed product. The descaling solution is to be disposed of according to the manufacturer’s instructions and/or regulations in force in the country of use. Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end. Never use vinegar as a descaling solution. (Fig.11 - 12) - Insert the Portafilter into the brew unit from the bottom (7) and turn it from left to right until it locks into place. 1 (Fig.2) - Remove and empty the water tank. 2 (Fig.4) - Pour the entire content of the Saeco concentrated descaling solution into the water tank, and then fill the tank with fresh drinking water up to the MAX level. 3 (Fig.7) - Turn the machine on by pressing the ON/OFF button (17) and dispense 2 cups (approx. 150 ml each) of water by using the steam / hot water wand (Fig. 8), then turn the machine off. 4 Leave the descaling solution to descale for approx. 15-20 minutes with the machine turned off. 5 (Fig.7) - Turn the machine on by pressing the ON/OFF button (17) and dispense 2 cups (approx. 150 ml each) of water by using the steam / hot water wand (Fig. 8). Then turn the machine off by means of the ON/OFF button (17) and leave it off for 3 minutes. 6 Repeat the operations as described from step 5 until the water tank is completely empty. 7 (Fig.4) - Rinse the water tank with fresh drinking water and fill it again. 8 Place a container under the Portafilter. 9 (Fig.7) - Turn the machine on by pressing the ON/OFF button (17); press the brew button (15) and by using the Portafilter, dispense the whole content of the tank. 10 (Fig.8) - Fill the tank again with fresh drinking water. Open the water dispensing knob (3) by turning it counter- clockwise. Press the button (15) and dispense the whole content of the tank by means of the steam / hot water wand. 11 After dispensing the water, press the button (15) again to end the operation; close the water dispensing knob (3) by turning it clockwise. 12 Remove the Portafilter from the unit by turning it from right to left and rinse it with fresh drinking water. The descaling cycle is complete. (Fig.8) - Fill the tank again with fresh drinking water. If necessary, prime the circuit as described in Sect...