Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Jura Capresso, модель IMPRESSA E50

Производитель: Jura Capresso
Размер: 618.12 kb
Название файла: 5e4e2f63-ce78-4847-8dae-9a474e8d7426.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Warning lamp does not go out until the complete decalcifying process has been carried out. 11.6 Use of Claris filter cartridges At the correct use of Claris filter cartridges, decalcifying of the machine becomes unnecessary. For further information, please read the instructions for use attached to the water tank. Note: Furring display must be switched off (as described in chapter 3.6) before using Claris filter cartridges. 11.7 General cleaning instructions Never use sharp or abrasive articles or corrosive chemicals to clean your machine. Wipe down the casing inside and out using a soft damp cloth. Clean the pivoting hot-water/steam nozzle every time it is used. After warming milk, draw off a little hot-water to clean the pivoting nozzle inside. You can take off the pivoting nozzle for a thorough cleaning (Fig. 8). The water tank should be rinsed out and filled with clean water daily. Note: If you notice any furring in the water tank, this can be descalcified separately with a customary decalcifying product. Remove the tank from the machine in order to do this. 11.8 Regular servicing Regular Jura services ensure your machine’s reliability and longer life. Keep the original packaging to protect the machine when it is transported. 11.9 Empty system Important: This process is necessary to protect the machine from frost damages while being transported. Press button to switch off the machine. Place a container under the pivoting nozzle (13) Turn selector switch for hot-water/steam (12) to position . Press button to switch on the machine. Warning lamps , , , flash. Press button until only warning lamp flashes. Steam comes out after a short time. Draw off steam until it stops automatically. Turn selector button for hot-water/steam (12) back to position The machine has an integrated cleaning program. . 12. Cleaning Note: Whenever the machine needs cleaning, warning lamp lights up. You can still draw off coffee and hot-water/ steam and run the cleaning program later. Only use Jura cleaning tablets. These are available from your Jura dealer. Important: It is essential not to interrupt the process once it has been started. Switch on machine by pressing button. Push button for about 3 seconds. Warning lamps , (if necessary) , light up. Fill water tank. Empty drip tray and grounds container and replace them. Warning lamps (if necessary) go out. Place a container under the coffee-spout (9). Put a Jura cleaning tablet (Fig. 9) into the powder funnel (10). Press selector button . The warning lamp goes out. Warning lamp flashes. The flashing of warning lamp indicates that the cleaning process is activated. If warning lamp lights up, empty drip tray (if necessary), wait about 10 seconds before replacing it. Warning lamp goes out. Replace the container under the coffee-spout (9) and press button . The cleaning process is continued. If warning lamp lights up again, empty drip tray (if necessary), wait about 10 seconds before replacing it. Warning lamp goes out. Replace the container under the coffee-spout (9) and press button . The cleaning process is continued. At the end of it, warning lamp lights up. Empty drip tray and grounds container and replace them. Warning lamp lights up. Replace container under the coffee spout (9) and press button . The machine rinses and warning lamp lights up. Tip: Clean powder funnel with a bottle-brush. 13. Decalcifying Your machine has an integrated decalcifying program. If a Claris filter cartridge is used there is no need for decalcifying your machine. Please use Jura decalcifying tablets only. These are available from your Jura dealer Note: If the machine needs decalcifying warning lamp lights up. You can still draw off coffee and hot-water/steam and run the decalcifying program later. Important: Run the decalcifying program only after the machine has been switched off for at least 2 hours and has cooled down completely. The decalcifying program is started with the machine switched off. The running decalcifying program must not be interrupted. Switch off machine by pressing button and let the machine cool down for 2 hours. Then remove water tank. Press button for about 3 seconds. Warning lamps , , light up. Pour 0,5 litres of water into a container and completely dissolve the contents of a blister pack (2 tablets). Then fill the mixture into the water tank. Empty drip tray and replace it. Warning lamps , , , flash and warning lamp lights up. Place a sufficiently big container under the pivoting nozzle (13). Turn selector switch for hot-water/steam (12) to position . 13 E The flashing of warning lamp indicates that the decalcifying program is activated. If warning lamp lights up, empty drip tray (if necessary). Warning lamps , , , flash and warning lamp lights up. Turn selector switch for hot-water/steam (12) back to position . The decalcifying program is continued and the decalcifying solution is channelled inside the machine to the drip tray. Warning lamp...

Эта инструкция также подходит к моделям:
Кофеварки - IMPRESSA E55 (618.12 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории