Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
HIGH, strength (flavor) STRONG ADJUSTABLE SETTINGS 1 cup from 0.5 to 8 oz. 2 cups from 0.5 to 8 oz. per cup Note: when using the 2-cup option, ENA will always grind in the STRONG setting. Please note: You can change all above pre-sets (chapter 14a). You can also override the strengths and the cup size before/ during actual brewing. Overriding will not change the preset values (chapter 9d). Other functions are set as follows (to change functions refer to listed chapters.) chapter Filter (Clearyl)...................– not installed ..... 17.1 Hardness Level............... 10. dH .................. 16.1 Auto-Off.......................... 2 Hours................. 20 Grinder Fineness ............Middle position .... 7 Energy Saving ................ – not set.............. 19 Unit (Volume) ................ in OZ ................... 21 Language ....................... English ................. 22 3-Color Display The ENA features a 3-color alpha-numeric display. This facilitates the use even more. Green: ENA is ready to prepare a beverage or is in the process of preparing a beverage. Red: ENA is requiring some kind of action from you to get back to the green display (e.g. FILL WATER TANK) Yellow: ENA is in programming mode (you pushed the P button). To get out of the programming mode, push the P button again and the display will show the previous information. 6. PREPARING ENA FOR THE FIRST TIME Make sure • all accessories, literature, caution leaflets etc. are removed from the machine, the water tank, and the bean container. • the Clearyl Water Filter is NOT installed! • the machine sits on a flat, even surface and the drawer, tray and used coffee container are inserted (Fig. 1, 12-13). 12. • machine is NOT placed on a surface which is sensitive to heat, water and steam. • Plug-in machine. 6.1 TURNING THE MACHINE ON • Press the On/Off button on top of the machine (Fig 1,2). The display will illuminate. FILL WATER TANK 6.2 FILLING THE WATER TANK Please note: Only use fresh, cold water. Never fill water tank with carbonated water, milk or any other liquid. • Remove the water tank (Fig. 1.1), rinse and fill with fresh, cold water. • Replace water tank and close lid. Display shows OPEN TAP. • Place a cup underneath the frother and turn the Selector Switch to the hot water/steam position (Fig. 5). The display shows SYSTEM FILLING. The ENA starts pumping water into the system, until water comes through the frother. After a few seconds the process stops and the display shows CLOSE TAP. Turn Selector Switch to the coffee position. HEATING. • Place a cup underneath the coffee spout. After approx. one minute the display shows PRESS ROTARY. • Push down on the Rotary Dial (Fig.4). Warm water pumps through the coffee spouts and stops. Display shows READY. 6.3 ABOUT COFFEE BEANS Frozen Beans: Thaw 3 to 4 hours before adding to bean container. This prevents moisture from seeping into the grinder. Oily Beans: Beans with an oily surface tend to stick together. This may prevent a continuous flow of beans from the bean container into the burrs. As a result the grinder does not grind enough coffee and you might get weak or no coffee at all. Before filling oily beans into the bean container pour the beans in an open bowl and let them sit for about 5 hours. The oils will evaporate (this will not change the taste of your coffee). Then fill the beans into the bean container. Now beans will feed into the burr grinder more easily. Flavored Coffee: DO NOT use flavored beans in the grinder! If you like flavored coffees we recommend to add flavors to your coffee after brewing. This way you can use your regular coffee beans in the bean container. Adding the flavors after brewing lets you control the intensity better than with pre-flavored coffee. Your local coffee store typically carries a variety of flavors. 6.4 FILLING THE BEAN CONTAINER Please note: To insure that your conical burr grinder will work for a long time, do not use it with any kind of coated or flavored beans (all coating and flavors contain sugar or sugar substances). Such coating can damage the burrs. Using such beans voids the warranty. Have your coffee store grind the sugar coated beans and use as described in the chapter 10. • Remove the Bean Container Lid (Fig. 1, 3). • Fill beans into the bean container. The container holds approximately 4 oz. (125g) of beans. • Place an 8 oz. cup underneath the Dual Coffee Spout and push the Rotary Dial. During coffee preparation the display sequence changes as follows: READY... NORMAL...1 CUP... READY. • If the display shows FILL BEANS push the Rotary Dial again. • Discard the first two cups of coffee. READY. Your next cup of coffee will be perfect. 13. 7. ADJUSTING THE GRINDER The Grinder Fineness Adjustment Ring is set to a medium grind position. We recommend leaving the grinder in this position for most applications. Please note: You can only adjust the grinder during grinding. • If you have extremely dark roasted, oily beans, set the ...
Эта инструкция также подходит к моделям:Кофеварки - 68191 (291.2 kb)
Кофеварки - ENA 4 (291.2 kb)
Кофеварки - ENA 5 (291.2 kb)