Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
z To create another program Press p(CLEAR) until the order on the program returns to 0 and the cursor flashes above track number 1 in the display, then follow Steps 2 to 5 on page 9. z You can use your Sony remote to perform RMS programming If your Sony stereo receiver’s remote has RMS buttons, do the following steps. 1 Turn on the receiver and press TAPE. 2 Press RMS/START. 3 Press aor » to select the front or reverse side of the tape, and the number keys and the >10 key to specify the tracks. 4 Press RMS/START again to start RMS Play. Note For more information on the availability of Sony stereo receiver remotes with RMS capability, contact your nearest Sony dealer. Advanced Recording Operations Advanced Recording Operations Adjusting Bias and Recording Level Calibration Automatically Since there are many different types of cassettes on the market, your tape deck automatically sets the appropriate equalization characteristics and bias current for each tape type (ATS: Automatic Tape Selection). However, you can get better recording results by doing the automatic bias current and the recording level calibration. DECK A / DECK B »/ · PAUSE P» / aPAUSE P ¤ Rr ¤ Rrp»a 0)(AMS) (AMS) 0)(AMS) (AMS) p»a 0 1 2 3 4 5 6 7 8 9 10 1 Insert the cassette you want to record on into either deck. Make sure the record-protect tabs on the cassette have not been removed. 2 Press DECK A or DECK B until “CAL” appears in the display. 3 Press aor »to select the side of the tape to be recorded. To select Press The front side · The reverse side . 4 Press PAUSE Pto start the automatic calibration procedure. The automatic calibration procedure starts (i.e., recording test tones, rewinding, and playing back). During the calibration, the counter changes from 9 to 0. CA.L9 CAL B REC When the automatic calibration procedure ends, the tape rewinds to the original position, the counter returns to normal and the tape deck stops. 5 Start the actual recording (see page 6). To cancel the automatic calibration function Press p on the deck you’re using. If “A” or “B” flashes continuously The automatic calibration procedure has been interrupted by: — The end of the tape. Reverse the tape direction or rewind the tape to a new position that allows recording of the test tone. — Damaged tape or dirty heads. Change the cassette or clean and demagnetize the heads (see page 19). Updating the calibration setting If you insert a cassette and “[A] CAL” or “CAL [B]” appears in the display, it means that automatic calibration data in that deck for that tape type (I, II or IV) exists. However, we recommend that you repeat the automatic calibration procedure each time you insert a new cassette since cassettes of the same type also vary in their characteristics. Before recalibrating, be sure to turn off “[A] CAL” or “CAL [B]” by pressing DECK A or DECK B. Then start from Step 2 of the automatic calibration procedure. Advanced Recording Operations Advanced Recording Operations Adjusting the Recording Level Automatically (Auto Rec Level) The Auto Rec Level function automatically measures the peak signal level and adjusts the recording level accordingly. The Auto Rec Level function operates during normal recording, Relay Recording or Simultaneous Recording on either deck. AUTO indicator REC LEVEL ARLPAUSE PREC ra¤ PRr ¤ Rrp»a 0)(AMS) (AMS) 0)(AMS) (AMS) p»a 0 1 2 3 4 5 6 7 8 9 10 1 Follow Steps 1 to 3 of “Recording on a Tape” on page 6. Make sure that record-protect tabs on the cassette have not been removed. 2 Press REC r. The AUTO indicator flashes and the deck automatically adjusts the recording level. The AUTO indicator lights up continuously after the recording level has been adjusted. 3 Press PAUSE Por a. Recording starts. To cancel the Auto Rec Level function Press ARL or turn REC LEVEL so that the AUTO indicator goes off. If you do either of these during recording, recording will continue but with the Auto Rec Level function turned off. To stop recording Press p. z How the Auto Rec Level function adjusts the recording level While the AUTO indicator is flashing, the deck sets the recording level as high as possible without causing distortion. If the signal level rises excessively after the start of recording, the deck gradually decreases the recording level. z You should adjust the recording level manually with REC LEVEL in the following cases: —The recording level cannot be adjusted properly due to excessive noise in the program source. —The program source level is too low and the recording level does not increase. During a quiet passage in a program source such as classical music, the recording level may not increase for some time. If a high sound level is expected later on in the track, play that portion first so that the right adjustment can be obtained. —The recording level does not decrease for a long time. The Auto Rec Level function may not work properly when you try to record sound produced by a graphic equalizer that has extremely high-level signals...
Эта инструкция также подходит к моделям:Кассетные деки - TC-WE625 (267.21 kb)
Кассетные деки - TC-WE825S (267.21 kb)