Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
z To use headphones Connect them to the PHONES jack. Use PHONE LEVEL to adjust the volume. 1 1 Turn on the amplifier and set the source selector to the position for DAT. 2 2 Press POWER. 3 3 Press OPEN/CLOSE ¤and insert a cassette. Window side up OPEN/CLOSE OPEN/CLOSE ¤ b b ¤ Close the cassette holder by pressingInsert the cassette OPEN/CLOSE ¤. beyond the silver bar. 4 4 Press a. The deck starts playing. Adjust the volume on the amplifier. To Press Stop playing p Go to the next track ± Go to the preceding track . Fast-forward or rewind )or 0when the deck is stopped Fast-forward or rewind while monitoring the sound )or 0during playback. Release the button to resume normal playback. Take out the cassette OPEN/CLOSE ¤after stopping playing 3-858-189-21(1) Recording Operations Recording Operations For basic recording operations, see pages 6 and 7. Things You Should Know Before Recording The difference between a blank section and a sound-muted section The deck distinguishes between two kinds of silent sections, which are respectively called a “blank section” or “sound-muted section”. Blank section This is a section on which no signal has ever been recorded. a) a) a) a) ....b) b)......b)....b).., Blank section a): Recording b): Track Sound-muted section This is a section on which a signal has been recorded but at a level that is not audible. a) ....b) b)......b)....b).., Sound-muted section a): Recording b): Track Important Make sure no blank sections are created while you are recording. The existence of blank sections within recorded material will make search operations using the /±buttons impossible or destroy the continuity of the absolute time codes. z If you press the r REC button while in a blank section The deck automatically rewinds the tape to the beginning of the blank section and changes to recording pause (except during Timer Recording). Absolute time codes Absolute time codes indicate the elapsed time from the beginning of the tape. These codes are automatically recorded. Note that once recorded, absolute time codes cannot be re-written. For accurate recording of absolute time codes • If the tape is blank, make sure to start recording from the beginning of the tape. • Use Record Muting (see page 12) to insert spaces between tracks. Do not advance the tape with the aor ) button. • To start recording from the middle of a tape, use End Search (see page 10) to locate the end of the recorded portion. This will prevent the creation of blank sections. If “EMPHASIS” appears in the display The deck is recording a digital signal with emphasis (in the higher frequencies). The recording will also contain the same emphasis. If the deck is left in recording pause for more than 10 minutes Recording pause will be released automatically, the deck will stop and “SOURCE” will appear in the display. To resume recording, press rREC. The deck will change to recording pause. When using a new tape Before you record on a new tape, we recommend that you fast forward the whole tape and then rewind to the beginning to make the tape reel smoothly. Basic Operations 9 3-858-189-21(1) Recording Operations Recording Operations Adjusting the Recording Level for Analog Recording Before you start recording an analog source through ANALOG IN, set INPUT to ANALOG and adjust the recording level. REC LEVELaPMARGIN RESET PHONES REC MUTE REC AMS MODE RESET RESETERASEWRITEREHEARSALRENUMBERAUTO MARGIN OFFREC PLAY TIMER POWER gSTART ID PHONE LEVEL 100 ¤ pPrR)0±a OPEN/CLOSE ANALOG OPTICAL COAXIAL • • • REC LEVELINPUT 48 kHz 44.1 kHz LONG • • • •• REC MODE STANDARD SBM ON OFF L R 5 4 0 6 10 3 1 7 9 2 8 • • • • •• • • • • 1 Do steps 1 to 6 of “Recording on a DAT” on pages 6 and 7. 2 Play the portion of the program source with the strongest signal level. 3 While monitoring the sound, turn REC LEVEL to adjust the recording level so that the peak level meters are at maximum level without entering the OVER (red) range. 1.0 Maximum level MARGIN indication Remains unlit The segments of the peak level meters corresponding to the maximum signal strength remain lit longer than normal. The MARGIN indication shows the margin between maximum signal strength and 0 dB, changing each time a stronger signal. If the level exceeds 0 dB The segments under “OVER” light up, and “0.0 dB” flashes in the display. If these segments light steadily, sound distortion may occur. To avoid this, keep the recording level between –12 dB and 0 dB. To reset the margin indication Press MARGIN RESET. The margin indication changes to “- - dB”. 4 Stop playing the program source. 5 To start recording, press P or a, then start playing the program source. Locating the End of the Recorded Portion (End Search) End Search detects a blank section longer than 9 seconds, then automatically rewinds the tape to the end of the recorded portion, then stops. Use End Search to start recording from the end of the recorded portion without creating a blank section on the tape. 0/ ) PHONES REC MUTE RE...