Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
WARNING: FAILURE TO USE MANUFAC- TURE PROVIDED PARTS, VARIATIONS IN TECHNIQUES AND CONSTRUCTION MA- TERIALS OR PRACTICES OTHER THAN THOSE DESCRIBED IN THIS MANUAL MAY CREATE A FIRE HAZARD AND VOID THE LIMITED WARRANTY. Chimney and Termination NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 1 TYPICAL INSTALLATION PRECAUTIONS Note:These fireplace systems are not difficult to install. However, in the interest of safety, it is recommended that the installer be a qualified or certified“tradesman”familiar with commonly accepted fireplace installation and safety techniques as well as prevailing local codes. The most important areas of concern dealing with the installation of factory-built fireplaces are clearances to combustible materials, proper assembly of component parts, height of the chimney system, the proper use of accessories supplied by the manufacturer and the techniques employed in using finishing materials applied to the wall surrounding the fireplace, hearth extensions and wall shields. Each of these topics will be covered in thorough detail throughout this manual. Please give each your special attention as you progress with your installation. INTRODUCTION General Information These fireplaces are conventional radiant heat fireplaces with standard bar grates, optional outside combustion air kits and optional decorative glass doors. Note:Illustrations shown reflect“typical”installations with nominal dimensions and are for design and framing reference only. Actual installations may vary due to individual design preferences. However, always maintain minimum clearances to combustible materials and do not violate any specific installation requirements. These fireplaces have been tested and listed by Warnock Hersey (Report No. 629-915173) to U.L. standard 127. These units are intended for installation in residential homes and other buildings of conventional construction including commercial, not in mobile homes. These fireplace systems are designed for installation in accordance with the National Fire Protection Standard for chimneys, fireplaces and solid fuel burning appliances; NFPA 211 and in accordance with codes such as the BOCA Basic/National Codes, the Standard Mechanical Code and the Uniform Building Codes. WARNING: FAILURE TO USE MANUFAC- TURE PROVIDED PARTS, VARIATIONS IN TECHNIQUES AND CONSTRUCTION MA- TERIALS OR PRACTICES OTHER THAN THOSE DESCRIBED IN THIS MANUAL MAY CREATE A FIRE HAZARD AND VOID THE LIMITED WARRANTY. Chimney and Termination 1. The Fireplace 2. The Chimney and Termination 3. The Optional Glass Doors 4. The Optional Combustion Air Kits CLEARANCES AND HEIGHT REQUIREMENTS The fireplace may be placed on or near normal construction materials*. The combustion air kit, firestop spacer and roof flashing (not chase flashings) may be placed directly on or against normal construction materials.* The chimney and fireplace outer wrapper require a minimum 2" air space to combustibles. A combustible mantle may be installed 12" above the opening of the fireplace as per NFPA 211, Section 7-2.3.3. The minimum installed height of the completed fireplace system is 15' 6". The maximum height is 80' 0". The fireplace and chimney system must be enclosed when installed in or passing through a living area where combustibles or people may come in contact with it. This is important to prevent possible personal injury or fire hazard. For questions, please call your distributor or the manufacturer. Special restrictions apply to the front and facing of the fireplace and nearby walls (See pages 16 and 17 ). CHIMNEY SYSTEM These fireplaces are designed and code listed for use with Security Chimneys FTF13 chimney System only. Always use Security Chimneys FTF13 chimney components with these fireplaces. Do not modify or alter these components as this may cause a potential serious hazard and void the Warranty. *Construction Materials: • framing materials •paneling • particle board •flooring • millboard •dry wall • plywood •etc. Insulate Joists 19" Same As Ceiling (483mm) WARNING: DO NOT PACK OR FILL RE- QUIRED AIR SPACES WITH INSULATION OR OTHER MATERIAL. NO MATERIAL IS ALLOWED IN THESE AREAS. Draft Stops Note: Non- Combustible Chase Flashingmust be Used to Cover Chase Opening OptionalInsulation in Outside Walls of Chase Solid Continuous Surface Outside BaseInsulation (Thermal Barrier) 8' (2.4m) Level F10FS-2 Firestop FTF13-CT2 Termination 19" (483mm) Insulate Joists 19" Same As Ceiling (483mm) WARNING: DO NOT PACK OR FILL RE- QUIRED AIR SPACES WITH INSULATION OR OTHER MATERIAL. NO MATERIAL IS ALLOWED IN THESE AREAS. Draft Stops Note: Non- Combustible Chase Flashingmust be Used to Cover Chase Opening OptionalInsulation in Outside Walls of Chase Solid Continuous Surface Outside BaseInsulation (Thermal Barrier) 8' (2.4m) Level F10FS-2 Firestop FTF13-CT2 Termination 19" (483mm) Note: Do not insulate the chase cavity with blown or fill type insulation materials. Note:Local codes may not require firestopping at the ...