Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
FIGURE 9a-c The fireplace requires a minimum enclosure height of 39”. For temperature requirements, the enclosure space around and above the fireplace must be left unobstructed. W415-0298 / K / 12.06.07 FINISHING HOODGRATE AND LOG INSTALLATION FINISHING HOODGRATE AND LOG INSTALLATION 1. Remove curtain mesh and rod assembly 2. Remove log carton 3. Remove grate from the lower control area (stored there when shipped) 4. Unscrew the 3 screws in the firebox, set grate in place and secure using the 3 screws that were just removed. See Figure 11. 5. Install the one piece logset by aligning the two holes on the bottom of the logs, with the two locating pins in the firebox. NOTE: PHAZERTM logs and glowing embers exclusive to Continental® Fireplaces, provide a unique and realistic glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fi replace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. 6. Reinstall rod assembly and mesh curtain FIGURE 10 CHARCOAL EMBERS Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner. Fine dust found in the bottom of the bag should not be used. GLOWING EMBERS Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of the small logs (#2 & #3). Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame; however, care should be taken to not block the burner ports. Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM logs glow when exposed to direct flame. Use only certified “glowing embers” and PHAZERTM logs available from your Continental ® dealer. W415-0298 / K / 12.06.07 HOOD CURTAIN MESH FIGURE 11 The curtain mesh must be kept fully closed during operation to help prevent accidental burns from occurring. FIGURE 12 The heater must not be used when the hood is re- moved. Hook the hood over the lip of the curtain support plate. LOGO PLACEMENT Remove the backing of the logo supplied and place on the screen cover, as indicated. FIGURE 13 L36 LOUVRE INSTALLATION L36 LOUVRE INSTALLATION A C B FIGURE14 INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE. FIGURE 15 If the fireplace was not previously equipped with a blower: route a grounded 2-wire, 60hz power cable to the junction box. At this point, it must be strain relieved and insulated. The three slots on the blower mounting bracket allow ease of adjustment when attaching the blower. For a quiet running blower, do not allow the assembly to sit on the fi rebox base. FIGURE 16 If optional blower kit is to be installed, remove thermodisc from the bracket supplied in the kit and disgard the bracket. Install thermodisc in the bracket supplied with the fi replace. It is recommended to attach the wires to the disc and install A CLIPS CENTRE SLOT FLANGE SLOT TAB B C HINGE CLIP SLOT HOOD Attach the hood by pressing the top flange into the clips along the top of the louvre opening. Secure using a screw through the centre slot. UPPER LOUVRES Insert the louvre tabs into the slots located at the top left and right corners of the unit. LOWER LOUVRES Insert the hinge clips into the slots located at the bottom left and right corners of the unit. To remove the louvres, pull the back tabs of the clips forward, while pushing the louvre assembly back. Lift the clip. the bracket before installing the blower. Attach the black and white wires to the disc, then secure the bracket to the stud at the bottom left on the unit using the lock washer and wing nut. Ensure that the thermodisc touches the firebox wall. Slide the vibration reducing pad (A) into the clip (C) and up against the threaded stud (B) at the other end. The blower must be able to be positioned entirely onto the pad. Tilt the blower onto its side. Slide it past the controls and into the clip (C). Secure to the threaded stud using the lock washer and wing nut provided. Ensure that the blower does not touch the fireplace base or the firebox. C A B FIGURE 17 FIGURE 18 OPTIONAL BLOWER INSTALLATION W415-0298 / K / 12.06.07 FIGURE 22 Slide the fan assembly past the controls and into FIGURE 22 Slide the fan assembly past the controls and into FIGURE 19 Attach the connectors from the black and red wires to the blower. Attach and secure the variable speed switch using the nut provided. Plug the harness cord into the receptacle. FIGURE 20 The wire harness provided in this kit is a universal harness. When installed, ensure that any excess wire is contained, preventing it f...
Эта инструкция также подходит к моделям:Камины - CVF36N (781.03 kb)