Оценок - 3, средний балл: 3.7 ( )

Производитель: Stovax Размер: 603.72 kb Название файла: Язык инструкции:

1.4 THERMOSTATIC AND TIMER REMOTE CONTROL. This remote controls the gas appliance after the pilot has been lit. In ‘MANUAL MODE’ it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner leaving the pilot burning. In ‘AUTO MODE’ it will automatically regulate the room temperature to a pre-set temperature. In ‘TIMER MODE’ it will turn the fire on and off according to a pre-set programme and automatically regulate the room temperature during the two ON periods. GAZCO PART NUMBER 8456. 2.1 This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance. 2.2 All the instructions must be left intact with the user. 2.3 In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution. 2.4 This appliance is intended for use on a governed gas installation and set to the required pressure. 2.5 Keep all plastic bags away from young children. 2.6 Do not place any object on or near to the stove. Allow adequate clearance above the stove. See diagram 2 above, Appliance Location. 2.7 The stove is fitted with the Gazco Flue Sure System, which acts to cut off the gas supply to the appliance in the event of incorrect operation of the flue. If the system acts to shut INSTALLATION INSTRUCTIONS INSTALLATION 1. CONTROL UPGRADE 2. SAFETY PRECAUTIONS 3. INSTALLATION OF THE STOVE 3 4. GAS SUPPLY 13 There is a cutout in the RH rear leg to enable a direct straight connection to be made to the rear of the stove. See diagram 3. A gas soundness check must be completed up to the gas inlet connection. 4.2 Check the pull of the flue system by applying a lighted smoke pellet to the flue system opening. If there is a definite flow into the chimney, proceed with the installation. If not, warm the chimney for a few minutes. IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY REQUIRE ATTENTION - SEEK EXPERT ADVICE 4.3 The flue system may now be connected to the stove. Ensure that all joints are sealed with a suitable fire resistant sealant. It is also recommended that a physical retention method be used at the flue spigot joint, self-tapping screws are recommended.. 4.4 Connect a suitable pressure gauge to the test point located on the inlet fitting and turn on the gas supply. Light the appliance and check all gas joints for gas soundness. Turn the appliance to a maximum and check that the supply pressure is as stated on the databadge. Turn the gas off and replace the test point screw. Turn the gas on and check the test point for gas soundness. The major ceramic components can be found inside the firebox. Remove the cast iron door using the tool provided and remove all the protective packaging from these components. NOTE: THE CAST IRON IS HEAVY, TAKE EXTREME CARE WHEN HANDLING. Refer to ADVICE ON HANDLING AND DISPOSAL OF FIRE CERAMICS in User Instructions section 5. The loose coals should be arranged as specified in the following steps. Care should be taken to ensure there is sufficient space between the coals to allow flames to pass through. 5.1 Place the flame baffle onto the burner and push up against the rear tray lip, see diagram 4. 5.2 Locate the rear panel against the spacer brackets and slide down so that it locates on the ledge of the flame baffle, see diagram 5. 5.3 Locate the front coal between the heat shield and flame baffle so that its ends sit flat against the burner skin, see diagram 6. 5.4 Place five of the loose round coals on the front coal so that they lean against the flame baffle, in between the fingers. Place the two rectangular coals behind the round coals, one at each side, see diagram 7. 5.5 Place four of the loose round coals behind the first row so that they sit on the fingers, the two outer coals should touch the rectangular coals, see diagram 8. INSTALLATION INSTRUCTIONS INSTALLATION 5. FUEL BED ARRANGEMENT Small Clarendon 4 AR0359 5 AR0360 6 AR0361 7 AR0362 14 5.6 Place the remaining three round coals behind the centre row so that they touch the back panel, see diagram 9. 5.7 Ensure that the fibreglass seal on the back of the door is intact, locate the door on the four studs and slide back to the firebox. Secure in place using the four brass nuts and the tool supplied, do not over tighten the nuts, see diagram 10. Keep the tool with these instructions for future use. NEVER OPERATE THE STOVE WHEN THE DOOR IS REMOVED OR WHEN THE GLASS IS BROKEN. Go to page 17, COMMISSIONING. 5.8 Place the flame baffle onto the shelf at the rear of the tray and push up against the rear ledge, see diagram 11. 5.9 Locate the front coal moulding in front of the flame baffle ensuring that the end legs sit flat against the burner skin, see diagram 12. 5.10 Place t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: