Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Metal tabs and supports are needed for shipping only. After removing the tabs and supports, the grate should fully rest on the base refractory. 12 STEP 3: (SRV2057-721): Place log 2, nose to nose with log 1. The bottom notch on log #2 must mate over the log tab on the burner face. 2 1 A B 2 1 3 STEP 4: (SRV2057-722): Place log 3 so that the bottom notches mate with the 2 back steel tabs. Tab A is located on the right side of pilot bracket, tab B is located at the back/right corner of burner. NOTE: There should be a 1/2 inch gap between the bottom of log 3 and the top edge of the burner. The underside of log #3 must not cover ANY burner ports. 2057-935C Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev. P • 11/08 2 3 1 2 3 1 5 4 STEP 5: (SRV2057-723): Mate the top of log 4 with the STEP 6: (SRV2057-724): Notch in left end of Log 5 will right metal tab on log 3. The bottom of log 4 should touch interlock with front left corner of grate. Rest right end of log the inside face of the right grate tine. so that it engages tab on log 3. Log 2 may need to shift to right slightly. 2 35 6 1 C C 2 3 1 5 4 6 STEP 7: (SRV2057-725): Place log 6 on log 2 as shown. The left end of log 6 should touch the upper knot of log 2. The right end of log 6 should rest on the grate bar, centered between tine 4 and 5. NOTE: The front faces (C) of log 6 and 2 should be on the same plane. This is key in avoiding fl ame impingement. NOTE: Finished top view. Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev. P • 11/08 56 Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev. P • 11/08 L. Air Shutter Setting Air shutter settings should be adjusted by a qualifi ed service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.3. • Loosen the wing nut. • Push the air handle in to close the air shutter. • Pull the air handle out to open the air shutter. • Tighten the wing nut. NOTICE: If sooting occurs, provide more air by opening the air shutter. Figure 14.3 Air Shutter Figure 14.2 Fixed Glass Assembly H. Fixed Glass Assembly WARNING! Risk of Asphyxiation! Handle fi xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. • DO NOT strike, slam or scratch glass. • DO NOT operate fi replace with glass removed, cracked, broken or scratched. • Replace as a complete assembly. Removing Fixed Glass Assembly • Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 14.2). Replacing Fixed Glass Assembly • Replace the glass door on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame. I. Install the Mesh The screen mesh is built into front. Air Shutter Settings K. Install Trim and/or Surround • Install optional trim kits and/or surrounds using the instructions included with the accessory. • Use non-combustible materials to cover the gap between the sheet rock and the appliance (when applicable to the model). GLASS ASSEMBLY LATCHES (BOTH BOTTOM AND TOP) J. Hood Hood is included with the front and required in all installations. Note: The adjustable air shutter is not offered with the LP model. The LP is fi xed, full open, for maximum primary air. Model Shutter Settings 8000TR-OAK (NG) 3/8 inch 8000TR-OAK-IPI (NG) 3/8 inch 8000TRLP-OAKIPI (LP) Fixed AIR SHUTTER WING NUT 115 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician. A. Standing Pilot Ignition System Symptom Possible Causes Corrective Action 1. After repeated triggering of the red or black piezo ignitor button, the spark ignitor will not light the pilot. A. No gas or low gas pressure. Check the remote shut-off valves from the appliance. Usually, there is a valve near the gas main. There can be more than one valve between the appliance and the main. B. No lp in tank. Check the LP (propane) tank. You may be out of fuel. C. Ignitor. Check the spark at the electrode and pilot. If no spark and electrode wire is properly connected, replace the ignitor. Verify that there is no short in electrode wire. D. Pilot or misaligned electrode Using match, light the pilot. If the pilot lights, turn off the pilot and (spark at electrode). trigger the piezo ignitor button again. If the pilot lights, an improper gas/air mixture caused the bad lighting and a longer purge period is recommended. If the pilot will not light, ensure the gap at the electrode and p...
Эта инструкция также подходит к моделям:Камины - 8000TR-OAK (3.92 mb)
Камины - 8000TRLP-OAKIPI (3.92 mb)