Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Bend out the four nailing tabs, attached on either side of the fireplace and secure to the 2x4 framing. The tabs will facilitate the installation of either a 3/4” or a 1” finished surface thickness. The nailing tabs must not be removed. NAILINGNAILING TABTAB FIGURE 10 W415-0369 / E / 02.16.07 FINISHING LOG PLACEMENT FINISHING LOG PLACEMENT PHAZERTM logs are exclusive to NAPOLEON® Fireplaces, and provide a unique and realistic glowing effect that is different in every installation. Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. FIGURE 11a-d SIDEVIEW TAB 1. Place the back log (#1) onto the log support tray and in front of the tabs. The tabs maintain an air space between the log and firebox back to facilitate combustion air flow. Ensure that the back of the log rests against the brackets on the back wall of the firebox. 2. Move the two small logs (#2 & #3) into position, lining up the studs located on the burner with the holes on the bottom 4. Position the notch located on the end of the center log (#5) against the middle grate post with the other end of the log resting in the pocket of the left crossover log. 5. Place the bottom of the right crossover log (#6) against the right firebox side and pulled forward to the grate. The top of the log should rest in the pocket provided on the center log (#5). Blocked burner ports can cause an incorrect fl ame pattern, carbon deposits and delayed ignition. PHAZERTM logs glow when exposed to direct flame.PHAZERTM logs available from your NAPOLEON® dealer. IT IS HIGHLY RECOMMENDED TO PROTECT THE LOGS FROM MOISTURE. COVER THE FIREBOX WHEN NOT IN USE. of the logs. Ensure that the small logs sit flat on the burner. IMPORTANT 3. Place the bottom of the left crossover log (#4) against the left firebox side and pulled forward to the grate. The top of the log should rest in the pocket on the back log. W415-0369 / E / 02.16.07 LOGO PLACEMENT HOOD LOGO PLACEMENT HOOD HOOD CURTAIN MESH FIGURE 12 The curtain mesh must be kept fully closed during operation to help prevent accidental burns from occurring. FIGURE 13 Remove the backing of the logo supplied and place on the screen cover, as indicated. FIGURE 14 LOUVRE INSTALLATION FIGURE 15a-c LOUVRE HOOD SLOT BRACKET A LOWER LOUVRES (VALVE CONTROL DOOR) B UPPER LOUVRES: Insert the upper louvres into the slots on both brackets. Press the top flange of the hood into the four clips located along the top of the unit as shown. LOWER LOUVRES: Attach each hinge to the firebox with 2 screws. The heater must not be used when the hood is removed. Hook the hood over the lip of the curtain support plate. HINGE SCREEN C HINGE SCREEN: Position the hinge screen into place and with the control door open, secure to the firebox using three screws. W415-0369 / E / 02.16.07 W415-0369 / E / 02.16.07 Do not use steel wool, as it will scratch the fi nish. Stainless steel parts will discolour when heated, usually to a golden or brown colour. This discolouration is normal and will not affect the performance of the appliance. When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed. 1. Stop! Read the safety information on the operating label. 2. Turn the gas knob clockwise to off. 3. Wait five (5) minutes to clear out any gas. If you smell gas including near the fl oor, stop! Follow “b” on the operating label. If you don’t smell gas go to the next step. 4. If fireplace is equipped with flame adjustment valve turn clockwise to off. 5. Find pilot located in front of back log. 6. Turn gas knob counter-clockwise to pilot. 7. Depress and hold gas knob while lighting the pilot with the push button igniter. Keep knob fully depressed for one minute, then release. If pilot does not continue to burn repeat steps 3 through 7. 8. With pilot lit, turn gas knob counter-clockwise t o on. 9. If equipped with flame adjustment valve, push and turn knob to high. 10. If equipped with remote on-off switch, main burner may not come on when you turn the valve to on or high. Remote switch must be in the on position to ignite burner. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous FIGURE 16 • Do not use a mobile or land phone. • If you cannot reach your gas supplier, call the fi re department. • Turn off all gas to the fireplace. • Do not try to light any appliance. • Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions. A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the fl oor. C. Use only your hand to turn the gas control knob / manual shut-off knob. Never use tools. If the knob will not turn b...
Эта инструкция также подходит к моделям:Камины - GSS36N (2.87 mb)