Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
W415-0297 / D / 04.03.03 FINISHING LOGO PLACEMENTHOOD HOOD CURTAIN MESH FIGURE 11 FINISHING LOGO PLACEMENTHOOD HOOD CURTAIN MESH FIGURE 11 The curtain mesh must be kept fully closed during operation to help prevent accidental burns from occurring. FIGURE 12 The heater must not be used when the hood is removed. Hook the hood over the lip of the curtain support plate. Remove the backing of the logo supplied and place on the screen cover, as indicated. FIGURE 13 CATALYTIC DOOR OPENING & CLOSING DOOR LATCH HOOD UPPERLOUVRE FLANGE CLIP FIGURE 14 CATALYTIC DOOR OPENING AND CLOSING (IF APPLICABLE): The upper louvres must be removed to allow the catalytic door to be opened or closed. To access the lower door latch, open the valve control door. Release the top and bottom door latches, located at the right side of the door. W415-0297 / D / 04.03.03 LOG PLACEMENT LOG PLACEMENT PHAZERTM logs and glowing embers exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. #1FIGURE 15a-f TAB SIDEVIEW 1. Place the back log (#1) onto the log support tray and in front of the tabs. The tabs maintain an air space between the log and firebox back to facilitate combustion air flow. Ensure that the back of the log rests against the brackets on the back wall of the firebox. #2 #3 2. Move the two small logs (#2 & #3) into position, lining up the studs located on the burner with the holes on the bottom of the logs. Ensure that the small logs sit flat on the burner. #4 3. Place the bottom of the left crossover log (#4) onto the stud on the left side of the log support. The top of the log should rest in the pocket on the back log. #5 4. Position the notch located on the end of the center log (#5) against the middle grate post with the other end of the log resting in the pocket of the left crossover log. #6 5. Place the bottom of the right crossover log (#6) against the right firebox side, so that it is cradled between the right outermost grate post and the right tab. The top of the log should rest in the pocket provided on the center log (#5). CHARCOAL EMBERS Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner. Fine dust found in the bottom of the bag should not be used. GLOWING EMBERS Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of the small logs (#2 & #3). Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame; however, care should be taken to not block the burner ports. Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM logs glow when exposed to direct flame. Use only certified "glowing embers" and PHAZERTM logs available from your Napoleon dealer. W415-0297 / D / 04.03.03 L36 LOUVRE INSTALLATION GVFL LOUVRE INSTALLATION LOUVRE HOOD SLOT BRACKET A FIGURE 16a-c L36 LOUVRE INSTALLATION GVFL LOUVRE INSTALLATION LOUVRE HOOD SLOT BRACKET A FIGURE 16a-c UPPER LOUVRES: Insert the upper louvres into the slots on both brackets. Press the top flange of the hood into the four clips located along the top of the unit as shown. LOWER LOUVRES (VALVE CONTROL DOOR) B LOWER LOUVRES: Attach each hinge to the firebox with 2 screws. HINGE SCREEN C HINGE SCREEN: Position the hinge screen into place and with the control door open, secure to the firebox using three screws. FIGURE17 A C B A CLIPS CENTRE SLOT FLANGE SLOT TA B B C HINGE CLIP SLOT HOOD Attach the hood by pressing the top flange into the clips along the top of the louvre opening. Secure using a screw through the centre slot. UPPER LOUVRES Insert the louvre tabs into the slots located at the top left and right corners of the unit. LOWER LOUVRES Insert the hinge clips into the slots located at the bottom left and right corners of the unit. To remove the louvres, pull the back tabs of the clips forward, while pushing the louvre assembly back. Lift the clip. W415-0297 / D / 04.03.03 OPTIONS OPTIONS 3. Screw the door hinge onto the heater by first starting each of the five machine screws and then tightening all screws. CURTAIN ROD BRACKET 1 TOP DOOR LATCH 4. & 5. Secure the door using the two latches. Install the appropriate hood by hooking it over the top lip of the door assembly. The heater must not be used when the hood is removed. 1. The mesh must be removed if the catalytic door is used. BOTTOM DOOR LATCH Remove the centre bracket and bend the curtain rod slightly to disengage the rod from either side. 2. Remove the curtain support plate. Remove the two latch securing screws, alr...
Эта инструкция также подходит к моделям:Камины - GVF36P (1.31 mb)