Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Any odors remaining after this initial break-in will be slight and will disappear with continued use. Standing Pilot Operating Instructions The standing pilot (750 millivolt system) is a continuous burning pilot. The pilot remains ON even when the main burner is OFF. 750 Millivolt System (Figures 40 and 41) When you ignite the pilot, the thermocouple produces millivolts (electrical current) which energizes the magnet in the gas valve. After 30 seconds to 1 minute time period you can release the gas control knob and the pilot will stay ON. Allow your pilot flame to operate an additional one (1) to two (2) minutes before you turn the gas control knob from the PILOT position to the ON position. This time period allows the millivolts (electrical current) to build-up to a sufficient level allowing the gas control to operate properly. 1. Follow the SAFETY and LIGHTING INSTRUCTIONS for standing pilot controls found in this manual and on labels found in control compartment behind the door assembly. CAUTION: During the initial purging and subsequent lightings, never allow the gas valve control knob to remain depressed in the "pilot" position without pushing the red ignitor button at least once every second. 2. During the heating season, leave the control valve knob in the "ON" position. This will allow the pilot flame to remain lit. Turn the burner flame on or off with the fireplace ON/OFF rocker switch, wall switch, remote control kit or 750 millivolt wall thermostat. NOTE: The gas control valve allows you to increase or decrease the height of the main burner flame. The control valve has a pressure regulator with a knob as shown in Figure 40. Rotate the knob clockwise to "HI" to increase the flame height and counterclockwise to "LO" to decrease the flame height. 3. When the heating season is over, turn the on/off switch to "OFF" and the control valve to "OFF". The system, including the pilot light, will be shut down. PIEZO IGNITOR HI/LO CONTROL KNOB Figure 40 The OWNER should carefully read and follow these operating instructions at all times. Lower the door assembly to view the gas controls for the fireplace. Your model has a push button piezo ignitor, the fireplace has a STANDING PILOT IGNITION SYSTEM. (See Figure 41) Follow the Safety, Lighting and Operating instructions applicable to your fireplace. PIEZOIGNITORPIEZO IGNITOR VALVECONTROLKNOBVALVE CONTROL KNOB VARIABLEREGULATORVARIABLE REGULATOR ("HI"-"LO")KNOB("HI"-"LO") KNOB REMOTE/ON/OFFSWITCHREMOTE/ON/OFF SWITCH DOORASSEMBLY(SHOWNOPEN)DOOR ASSEMBLY (SHOWN OPEN) GASVALVEGAS VALVE Figure 41 R-5627 Page 21 Initial Lighting Upon completing the gas line or turning the gas valve on after it has been in the "OFF" position, a small amount of air will be in the lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and operate satisfactorily. Subsequent lightings of the appliance will not require such purging if the gas valve is not turned to "OFF." Pilot Flame (Figure 42) The thermopile/thermocouple (standing pilot) tips should be covered with flame. Figure 42 Attention: Only, after the fireplace has been converted to a heater can the 750 millivolt wall thermostat, GWSG-T or battery operated remote control with thermostat, FRBTC-1 be used. See installation of heater baffle on Page 5. OPERATING INSTRUCTIONS ON/OFF/REMOTE Switch DVF is equipped with an ON/OFF/REMOTE switch. A wire harness is attached to the ON/OFF/REMOTE switch. The red, black and green (wires) female push-ons attach to the ON/OFF/REMOTE switch. At the opposite end of the wire harness, the black and green (wires) female push-ons attach to the gas valve. An additional green wire and the red wire, which are stripped and bare, will attach to the 750 millivolt wall thermostat accessory, or, to one of the other accessories that can be purchased for use with your log set. Operation of ON/OFF/REMOTE Switch with no Accessories To ignite main burner, turn the control knob on the gas valve from the PILOT position to the ON position. Turn the ON/OFF/REMOTE switch from the OFF position to the ON position. The additional green wire and red wire, which are stripped and bare are not used. Operation of ON/OFF/REMOTE Switch with Accessories 750 Millivolt Wall Thermostat, GWSG-T Connect the green and red, stripped and bare, wires on the ON/OFF/ REMOTE switch wire harness to the wall thermostat. Turn the ON/OFF/ REMOTE switch to the REMOTE position. Set the wall thermostat to the desired temperature. It is important to use wire of a gauge proper for the length of the wire: RECOMMENDED WIRE GAUGES Maximum Wire Length Gauge 1' to 10' 18 10' to 25' 16 25' to 35' 14 Wall Switch, FWS-1 Connect the green and red, stripped and bare, wires on the ON/OFF/ REMOTE switch wire harness to the wall switch. Turn the ON/OFF/ REMOTE switch to the REMOTE position. Pivot the rocker switch on the FWS-1 to the ON position. Bat...
Эта инструкция также подходит к моделям:Камины - DVF-36-2 (1.25 mb)
Камины - DVF-36IP-2 (1.25 mb)
Камины - DVF-42IP-2 (1.25 mb)