Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
We recommend that a qualified individual such as a plumber or gas fitter be hired to correctly size and route the gas supply line to the appliance. Installing a gas supply line from the fuel supply to the appliance involves numerous considerations of materials,protection,sizing,locations,controls, pressure, sediment, and more. Certainly no one unfamiliarandunqualifiedshouldattemptsizing or installing gas piping. Schedule 40 Black Iron Pipe Inside Diameter (Inches) Schedule 40 Pipe Length (feet) Natural Gas Propane Gas 0-10 1/2 3/8 10-40 1/2 1/2 40-100 1/2 1/2 100-150 3/4 1/2 150-200 3/4 1/2 Table 6 Notes: • All appliances are factory-equipped with a flexible gas line connector and 1/2 inch shutoff valve (see Figure 39 on Page 24). • See Massachusetts Requirements on Page 4 foradditionalrequirementsforinstallations in the state of Massachusetts in the USA. • ThegassupplylineshouldNotbeconnected to the appliance until Step 6 (Page 24). • Apipejointcompoundratedforgasshouldbe used on the threaded joints. Ensurepropane resistant compounds are used in propane applications. Be very careful that the pipe compound does not get inside the pipe. • It is recommended to install a sediment trap in the supply line as close as possible to the appliance (see Figure 39). Appliances using Propane should have a sediment trap at the base of the tank. • Check with local building official for local code requirements (i.e. are below grade penetrations of the gas line allowed?, etc.). IMPORTANT: If propane is used, be aware that if tank size is too small (i.e. under 100-lbs, if this is the only gas appliance in the dwelling. Ref. NPFA 58), there may be loss of pressure, resulting in insufficient fuel delivery (which can result in sooting, severe delayed ignition or other malfunctions). Any damage resulting from an improper installation, such as this, is not covered under the limited warranty. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 3. INSTALL THE VENT SYSTEM Step 3. INSTALL THE VENT SYSTEM These instructions should be used as a guideline and do not supersede local codes in any way. Install vent according to local codes,theseinstructions,thecurrentNational Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CSA-B149.1 in Canada. Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier. Degagementconformeauxcodesd'installation locaux et aux exigences du foumisseunde gaz. Use only approved venting components. See Approved Vent Components on Page 2. These fireplaces must be vented directly to the outside. The vent system may not service multiple appliances, and must never be connected to a flue serving a solid fuel burning appliance. The vent pipe is tested to be run inside an enclosed wall (such as a chase). There is no requirement for inspection openings in the enclosing wall at any of the joints in the vent pipe. Select Venting System - Horizontal or Vertical With the appliance secured in framing, determine vent routing and identify the exterior termination location. The following sections describe vertical (roof) and horizontal (exterior wall) vent applications. Refer to the section relating to your installation. A list of approved venting components are shown in the tables on Page 32. VERTICAL TERMINATION SYSTEMS (ROOF) VERTICAL TERMINATION SYSTEMS (ROOF) Both these vertical vent systems terminate through the roof. The minimum vent height above the roof and/or adjacent walls is specified in ANSI Z223.1-(latest edition) (In Canada, the current CAN/CSA-B149 installation code) by major building codes. Always consult your local codes for specific requirements. A general guide to follow is the Gas Vent Rule (refer to Figure 5 on Page 6). Vertical (Straight) Installation (Figure 16) Determine the number of straight vent sections required. 4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2" (572 mm), 34-1/2" (876 mm) and 46-1/2" (1181 mm) net section lengths are available (see Tables on this page and Page 32 - Vent Sections). Plan the vent lengths so that a joint does not occur at the intersection of ceiling or roof joists. Refer to the Vent Section Length Chart. Figure 16 SV4.5CGV-1 Termination SV4.5 F A OR SV4.5FB FlashingAND SV4.5SC STORM COLLAR .SV4.5VF Firestop/Spacer SV4.5L6/12/24/36/48 V ent Sections 40' Max. (12.2 M) 6' Min. (1.8 M) 1" (25.4 mm) Minimum Clearance to Combustibles . When using Secure Flex, use Firestop/Spacer SF4.5VF NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 441211 0 0 0 3 4 0515.210 1 0 0 3 4 5.451578.211 1 0 0 3 5 5.061573.310 2 0 0 3 5 5.271573.410 0 0 5 0 5 77157.411 0 0 5 0 6 38152.510 1 0 5 0 6 6815.510 0 0 0 4 4 5.091578.511 0 0 0 4 5 5.691573.610 1 0 0 4 5 5.502521.710 1 1 5 0 7 70252.710 0 0 6 0 6 5.112526.711 0 0 6 0 7 5.712521.810 1 0 6 0 7 5.922521.910 0 1 6 0 7 5.232573.910 0 0 0 5 5 73257.911 0 0 0 5 6 5.142521.020 0 0 7 0 7 6425.021 0 0 7 0 8 252120 1 0 7 0 8 462220 0 1 7 0 8 672320 0 0 8 0 8 97252.320 0 0 0 6 6 5.08257...
Эта инструкция также подходит к моделям:Камины - ADAGIO-EN (5.84 mb)
Камины - ADAGIO-MN (5.84 mb)