Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
If glass is broken, wear gloves and tape the remaining fragments onto the frame. 1. Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the firebox. Set assembly aside. 2. Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 42). 3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 42). 4. Remount the new frame at the hinge with five new screws before closing door. This will ensure seating of the gasket. 5. Close glass door frame. Lock latches by placing the bar under the tab on door and pushing down and back on latch (see Figure 42). 6. Replace screen/rod assembly by reversing step 1. 7. Replace louvers by reversing procedure under Removing Louver Panels, page 21. Latch FIREPLACE INSTALLATION Continued FIREPLACE INSTALLATION Removing/Replacing Glass Door (Cont.) Installing Lava Rock and Glowing Embers INSTALLING LAVA ROCK AND GLOWING EMBERS It is very important to keep logs exactly as installed. Do not modify logs. Only use log set designed for this fireplace. WARNING: Logs are unitized and are not attached to the burner. Do not handle log assembly by top logs. Always pick up by the bottom. Open louvers, remove screen, unlock door latches and open glass door. See Removing Glass Door, steps 1 and 2. 1. Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed front section of the burner (see Figure 43). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided. 2. Pour lava rock onto plenum but not onto flat burner. It is not necessary to use all of the lava rock provided. NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner will cause performance problems. 3. Close glass door, lock door latches, replace screen and close louvers (see Removing Glass Door, steps 5 through 7). WARNING: The glass door must be securely in place before running this fireplace. Do not run this fireplace if glass is missing or broken. Plenum Figure 43 - Placing Ember Material on Burner Cleaning Glass Door See Cleaning and Maintenance on page 27. Ember Material Andiron FIREPLACE INSTALLATION Installing Brick Liner Models BL36DA(SA) and BL36DHA(SA) OPERATING FIREPLACE For Your Safety Read Before Lighting Lighting Instructions 23 FIREPLACE INSTALLATION Continued INSTALLING BRICK LINER MODELS BL36DA(SA) AND BL36DHA(SA) WARNING: If fireplace has been running, turn off unit. Let cool before installing brick liner. You may purchase brick liner from your local retailer or see Accessories, page 36. CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels. 1. Remove top and bottom louvers to allow access to door latches. 2. Unlock door latches and open glass door. See Removing Glass Door, steps 1 and 2, page 22. 3. Carefully remove lava rock and ember material. 4. Remove andiron assembly from plenum by removing screws. 5. Carefully lift logs and ember pod from burner 6. Remove screws that attach plenum to burner to remove plenum. 7. Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside. 8. Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 44). 9. Install left side brick panel by sliding it between the burner assembly and the side of the firebox (see Figure 44). 10. Install the right brick panel using the same method described in step 6 for left brick panel. 11. Replace deflector shield using screws removed in step 7. Rear Brick Panel Left Side Brick Panel Figure 44 - Installing Rear Brick Panel 12. Using scews removed in step 6, replace plenum and attach to burner. 13. Carefully replace the ember pod and log set. 14. Use screws removed in step 4 to replace andiron assembly. 15. Install lava rock and glowing embers. See Installing Lava Rock 6and Glowing Embers, page 22. 16. Close glass door and lock latches on top and bottom of door andreplace screen. See Removing Glass Door, steps 5 and 6, page 22. 17. Replace top and bottom louvers. OPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly,afireorexplosionmayresultcausingproperty damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light an...
Эта инструкция также подходит к моделям:Камины - (V)KC36P (2.07 mb)