Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Light the fireplace as instructed in Lighting Instructions on page 23. Set wall thermostat to desired temperature. Thisthermostathasbeenelectronically calibrated atthefactory and requires no adjustment or leveling. Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation. To turn the fireplace off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit. IMPORTANT: To turn the pilot off, turn the gas control knob on the heater to the OFF position. OPERATING OPTIONAL BLOWER ACCESSORY Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the right side of the switch bracket to the left just inside the louver panel. TheBKmanualblowerandtheBKTthermostatically-controlled blower have an ON setting and an OFF setting. The blowerwill only run when the switch is in the ON position. In the OFFposition, the blower will not operate. Note for BKT Only: If you are using BKT blower with optional thermostat (wall mounted or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time.Thefireplacemayrunforseveralminutesbeforetheblowerturns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases. The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt or other obstructions that will hinder the flow of air. INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary. The height of the thermopile must be 3/8" to 1/2" above the pilot flame as shown in Figure 49. The thermocouple must be at a height of about 1/8" above the pilot flame. The flame from the pilot burner must extend beyond both the thermocouple and thermopile. If you pilot assembly does not meet these requirements: • turn fireplace off (see To Turn Off Gas to Appliance, page 24) • see Troubleshooting, page 28 Thermopile Pilot BurnerPiezoIgnitor 3/8" to 1/2" 1/8" Thermocouple Figure 49 - Pilot Assembly BURNER FLAME PATTERN Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions. If the vent configuration is installed incorrectly, the flames will lift or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance. Figure 50 shows a typical flame pattern. If burner flame pattern differs from that described: • turn fireplace off (see To Turn Off Gas to Appliance, page 24) • see Troubleshooting, page 28 Figure 50 - Typical Flame Pattern 116192-01B CLEANING AND MAINTENANCE Glass Door Pilot and Burners Logs Venting System 27 CLEANING AND MAINTENANCE WARNING: Turn off fireplace and let cool before cleaning. CAUTION:Youmustkeepcontrolareas,burnersand circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. GLASS DOOR WARNING: Handle glass door panel with care. Do not strike, slam or otherwise abuse glass. Do not operate fireplace with the glass door unlatched, removed, cracked or broken. WARNING: Do not use abrasive cleaners as this maydamageglass.Useanonabrasivehouseholdglass cleaner to clean glass. Do not clean glass when hot. Glass must be cleaned periodically. During start-up it is normal for condensation to form on the inside of the glass causing lint, dust and other airborne particles to cling to the glass surface. During initial start-up a slight film may form on the glass due to paint curing. The glass should be cleaned several times with a non-ammonia, nonabrasive household cleaner and warm water after the first two weeks of operation. Thereafter, clean the glass two or three times during each heating season, depending on the usage and circumstances present. Refer to Removing/Replacing Glass Door, page 21 of this manual when removing glass door for cleaning. WARNING: Only parts supplied by the manufacturer should be used when replacing broken or damaged glass door panel (see Replacement Parts, page 31). This glass door panel is a complete unit. No substitute materials may be used. CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass. If glass has been broken, carefully remove glass door (see Removing/ Replacing Glass Door, page 21). Vacuum all glass pieces ...
Эта инструкция также подходит к моделям:Камины - (V)TC36P SERIES (2.27 mb)