Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Heater Control Switch Heater ON/OFF switch, activates the heater C. Fan Control Switch Fan ON/OFF switch, activates the fan (purifier). HEATER CONTROL SWITCH MAIN POWER SWITCH FIGURE 2 FAN CONTROL SWITCH WALL MOUNTED CONTROLS The fireplace can be installed with wall mounted controls. These controls include wall switches and thermostats. (see installation guide for details) A. Wall Mounted Switches This model may be installed such that a wall mounted switch activates the flame effect and a wall mounted heater switch activates the heater (fan control switch on unit must be set at ON position). A wall mounted switch can also be installed to operate the heater independent of the flame. Fan control cannot be wired to a wall mounted switch. B. Wall Mounted Thermostat This unit may be installed such that a wall mounted thermostat can adjust the heat temperature to your individual requirements. Turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn the thermostat clockwise until you hear the click again and the heater will turn on. To turn the heater off, turn the thermostat counter clockwise all the way, and/or turn the manual heater switch on the unit to the OFF position. Fan control switch must be on to activate heater. THE TEMPERATURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating. Should the heater overheat, a red light (Fig. 1) will be activated and an automatic cut out will turn the heater off. The heater will re-activate once the heater has cooled. The overheat cutout will be triggered if the filter is dirty. Follow filter maintenance on page 8. CAUTION If the heater continuously resets, disconnect the power at the main service panel and call your local dealer. NOTE The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. MAINTENANCE WARNING Disconnect all power coming to fireplace at main service panel before attempting maintenance or cleaning to reduce risk of fire, shock or damage to persons. NOTE Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. TOOL RE QUIREMENTS Slot screwdriver LIGHT BULB REPLACEMENT Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There are four bulbs under the log set which generate the flames and embers. LIGHT BULB REQUIREMENTS Quantity of 4 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 watt rating. Example: GE 60BC or Philips 60CTC. DO NOT EXCEED 60 WATTS PER BULB. CAUTION When handling log only apply force to the ember bed section not directly to the logs. HELPFUL HINTS It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Long life bulbs are recommended to reduce the frequency of bulb changes. To access the light bulb area (BF33STP, BF39STP models) 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Examine the bulbs to determine which bulbs require replacement. 5. Unscrew bulbs counter clockwise. 6. Insert new bulbs. 7. Replace the log by inserting the rear tab of the logset under the back ledge of the fireplace and push down on the front edge of the logset until it snaps into place. (FIGURE 4) 8. Replace log grate using two screws previously removed. SCREWS 6 FIGURE 3 FIGURE 4 To access the light bulb area (BF33DXP, BF39DXP models) 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Set logset in front of firebox. 5. Disconnect the logset LED wire harness from unit. (FIGURE 5) 6. Examine the bulbs to determine which bulbs require replacement. 7. Unscrew bulbs counter clockwise. 8. Insert new bulbs. 9. Re-connect the logset LED wire harness to the unit. 10. Replace the log by inserting the rear tab of the logset under the back ledge of the fir...
Эта инструкция также подходит к моделям:Камины - BF33STP/DXP (278.79 kb)