Оценок - 3, средний балл: 3.3 ( )

Производитель: Regency Размер: 366.64 kb Название файла: Lennox_Hearth_GHC-GRD_Installation_700027.pdf Язык инструкции:

Outside Air Kit B Model No. A B GHC/GRD-5500 in. 36 15 1/2 mm 914 394 GHC/GRD-6500 in. 40 3/4 18 mm 1035 457 Rough Framing Face(Unfinished Shown) Outside Chase Installation Figure 8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. A Square Housing NotUsed on 5500 Model TYPICAL INSTALLATION SEQUENCE The typical sequence of installation follows, however, each installation is unique resulting in variations to those described. 1. Construct the appliance framing. 2. Route gas supply line to appliance location. 3. Position the appliance. 4. Install the vent system and exterior termination. 5.Field wire and install operating control switch. Install optional Forced Air Kit, if required 6. Make connection to gas supply. 7. Install optional Outside Combustion Air Kit, if required. 8. Install the logs and rockwool. 9. Install the optional glass doors/enclosure panel, if required 10. Checkout appliance operation. 11. Spillage Test and Safety Limit Switch Operation. 12. Adjust burner to ensure proper flame appearance. PRE-INSTALLATION NOTES The fireplace may be installed directly on a combustible floor or raised on a platform of an appropriate height. Do not place fireplace on carpeting, vinyl or other soft floor coverings. It may, however, be placed on flat wood, plywood, particle board or other hard surfaces, extending the full depth and width of the appliance. Be sure fireplace rests on a solid continuous floor or platform with appropriate framing for support and so that no cold air can enter the room from under the fireplace. The fireplace may be positioned and then the framing built around it, or the framing may be constructed and the fireplace positioned into the opening. Usually, no special floor support is needed for the fireplace, however, to be certain: 1. Estimate the total weight of the fireplace system and surround materials such as brick, stone, etc., to be installed. 2.2. 3. Note the floor construction, i.e. 2 x 6’s, 2 x 8’s or 2 x 10’s, single or double joists, type and thickness of floor boards. 4. Use this information and consult your local building code to determine if you need additional support. If you plan to raise the fireplace and hearth extension, build the platform assembly then position fireplace and hearth extension on top. Secure the platform to the floor to prevent possible shifting. INSTALLING THE FIREPLACE Step 1. Construct the Appliance Framing Frame appliance enclosure as illustrated in Figures 5 through 8 on page 6 and 7. (Note: Appliance may be positioned first and then the framing constructed around it.) If the appliance is to be elevated above floor level, a solid continuous platform must be constructed. IMPORTANT: UNDER NO CIRCUMSTANCES CAN THE FIREPLACE TOP SPACERS (FIGURE 2 OR 3 )BE REMOVED OR MODIFIED, NOR MAY YOU NOTCH THE HEADER TO FIT AROUND OR BE INSTALLED LOWER THAN THE SPACERS. THE HEADER MAY BE IN DIRECT CONTACT WITH THE TOP SPACERS BUT MAY NOT BE SUPPORTED BY THEM. Consult all local codes. Step 2. Route Gas Supply Line - Route gas line(Figure 5 )using techniques and materials prescribed by local and/or national codes. It is recommended that a gas line of ..." or greater diameter be used to allow full gas volume to the fireplace. Undue pressure loss will occur if the pipe is too small. The gas line should extend a total of 2 in. (51 mm) maximum into the appliance control compartment. When rigid pipe is used, an ANSI approved manual shut-off valve and union must be installed upstream of the fireplace. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream to prevent moisture and contaminants from passing through trap to the appliance controls and burners. Failure to do so could prevent the appliance from operating reliably. An external regulator must be used on all propane (L.P.G.) heaters to reduce the supply tank pressure to 13" w.c. (maximum). Any copper tubing used to supply propane (L.P.G.) from the tank must be internally tinned. IMPORTANT: HOLD GAS VALVE SECURELY TO PREVENT MOVEMENT WHEN CONNECTING TO INLET GAS LINE WARNING: CONNECTING DIRECTLY TO AN UNREGULATED PROPANE (L.P.G.) TANK MAY CAUSE AN EXPLOSION. Step 3. Position the Appliance - Slide the fireplace into prepared framing. (Note: Appliance may be positioned first and then the framing constructed around it.) Fireplace should be secured to side framing members using the full length ... inch nailing flanges that are integral to the appliance at each side. Use 8d nails (Figure 9 ). Note: The nailing tabs and the area directly behind the nailing tabs are exempt from the clearances described on the fireplace clearance label. 8d Nail Figure 9 Fireplace may be anchored to floor. Bend down four (4) anchor tabs located at the base of the fireplace and secure to the floor by nailing with 8d nails (Figure 10 ). Anchor Tab Figure 10 Step 4. Install the Vent System & Exterior Termination Connect a 5 in. (127 mm) Type B vent system to the appliance flue collar with four, No...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: