Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
CD-RW formatting software must first be properly Now let us review the hardware installation process, assuring that: installed in order to write CD’s with this device. l All connectors are properly connected. l Each SCSI device has its own unique SCSI ID number. l The last physical SCSI device on the bus is properly terminated. 1 49 50 Red Edge Notes l Red edge of 50 pin flat SCSI cable must be on pin 1 of host adapter. l The following is a sample configuration of CD-RW installation. 0 1 2 AUDIO OUT R GND L DC INPUT 5V ± 5% GND 12V ± 10% ACTIVE TERM TEST ID SELECT 1 2 49 50 CD-R/W Drive Power Supply Cable Red Edge SCSI Card (Not included) Speakers (Not included) Sound Card (Not included) Audio Cable (included) SCSI Cable (Not included) Step 10: Closing the Computer Carefully replace computer cover, per Owner’s Manual. Hardware installation is now complete! 14 Hardware Installation Using Discs Storing Discs . Do not store the disc in a location subject to: – high humidity – high temperature – excessive dust – direct sunlight Care of Discs . Only hold disc by its edge. Do not touch the record surface. . Do not wipe CD-R/RW discs before recording data. To avoid scratching the recording surface, blow away dust using an air blower. Software Installation/Using Discs 15 Operating Assure application software using the CD-RW drive. As the drive begins reading the Table of Contents (TOC) data, the busy indicator lights and remains illuminated until read is completed. When the busy indicator switches off, the drive is ready to receive Starting Up commands, data may be retrieved from the disc. After loading a disc, it takes a moment for the drive to become ready while Program Memory 1 Turn on the computer. Area is read. From this point, follow instructions provided with the 2 Press eject button and the tray extends from drive unit. application software. Eject button does not function if software disabled. Insert disc into drive slot with disc la acing up. Push gently until auto-load mechanism pulls tray into drive. Important: When loading a disc, do not attempt to o erpower the auto-load. Note: Busy indicator on drive continues to light amber if disc is not properly inserted or a malfunction occurs. In such a case, eject the disc (tray) and reinsert it properly. Should the light remain amber, consult your dealer or qualified service point. During audio play the busy indicator remains amber, this is normal. n Opening the drawer (tray) manually in an emergency In the event of electrical or mechanical drive failure, a manual emergency eject is provided to allow manual disc removal. Note: 1 Turn off the computer and remove power cable. 2 Insert a pointed object, perhaps a paper clip, into the emergency eject hole and push (typical force required is 46 N [4.7 kg]). at least 35 mm After thus removing disc, consult dealer or qualified service point. 16 Operating the Drive Operating the Drive 17 Troubleshooting Should problems occur while the drive: . Please verify the steps of this manual were carefully followed. . If problem still exists, please confirm the items in ”Checklist“ below. Checklist Please verify the following: . Power cable properly attached to drive, Step 8 on page 13. When properly connected, the LED lights. . Both ends of SCSI cable are properly attached, check pin 1 position. . SCSI ID# of CD-RW is unique to SCSI bus. Compare all other SCSI devices (internal and external) and see Step 2 – Step 5, pages 8-11. . Check all other jumpers on rear of drive. We recommend factory defaults on pages 10 and 11 with a SCSI ID# 6 (if possible). . Assure SCSI bus is properly terminated or activated at both ends. For details, please see Step 4, Termination, on page 9. Should you still have problems operating or installing your CD-RW drive, please contact our hotline or your local computer dealer. Additional Installation Cases ¦ No free SCSI connector present If other SCSI devices occupy ever bus connector, either remove a device before installing CD-RW drive or use a SCSI cable with more connectors. Please contact a local computer dealer for details. ¦ 68 Pin SCSI Cable If a wide SCSI cable (68 pin) is used, a 50 pin adapter is necessary. Technical If you require further support local Sony technical support professionals. For Europe (German or English) Tel.: +49 (0) 2389 - 951047 or SONY-HOTLINE@SUPLIE.COM (Monday – Thursday, 8:00 am – 4:30 pm / Friday, 8:30 am – 2:00 pm) For DK, N, SW & FIN, please call: Tel. +47 (0) 6281 8666 (Monday – Friday, 8:30 am to 4:00 pm Norwegian time) Within the UK, please call: Tel. 0870 900 8166 (Monday – Friday, 8:45 am to 5:00 pm) For France, please call: +33 (0) 155 870 866 (Monday – Friday, 9:00 am to 6:00 pm) or E-Mail: sony_hl@nati.fr All this information and more may be downloaded from the Internet. Simply access the following address: 18 Troubleshooting Technical Support 19 Specifications n General Host interface n Audio Line out: Headphone: n Environmental cond...
Эта инструкция также подходит к моделям:Калькуляторы - CD-R/RW (168.63 kb)
Калькуляторы - CD-R/RW (168.63 kb)
Калькуляторы - CD-R/RW (168.63 kb)