Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Replace them onto the opposite upper leg. Feet Feet Button Button L R 4 SHOWN ACTUAL SIZE Assembly 4 Lower Leg •Position a lower leg so that it stands on a flat surface, as shown. •Fit a foot onto the end of the lower leg. • Insert a #8 x 1/2" screw through the bottom of the foot and into the lower leg. Tighten the screw with a Phillips screwdriver. Do not over-tighten. •Repeat this procedure to assemble the other foot to the other lower leg. IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Foot •Position an upper leg so that the red dot is upward. •While pressing the button on the straight end of an upper leg, insert the upper leg into a lower leg. Make sure the but- ton on the upper leg “snaps” into the hole in the lower leg. •Repeat this procedure to assemble the other upper leg to the other lower leg. #8 x 1/2" Screw - 2 1 Red Dot Lower Leg Upper Leg Straight End Button Hole 2 •Locate the R and L on the underside of each elbow foot. The R indicates the right leg. The L indicates the left leg. •While pressing the upper button on the right leg, fit it into the tube in the motorized frame. Make sure the upper button on the right leg “snaps” into the hole in the tube. •Repeat this procedure to assemble the left leg to the motorized frame. •When the legs are assembled correctly to the tubes in the motorized frame, you should not see the red dots. Tube Hole Red Dot Motorized Frame ButtonElbow Foot L R 3 •Stand the assembly upright. •Pull the legs out so that the buttons “snap” into the holes in the motorized frame. •When standing behind the product, all four feet should be flat upon the floor. And, check for an L marking on the left foot and an R marking on the right foot. •If the feet are not flat upon the floor, or the left and right feet have been reversed, remove both lower legs from the upper legs. Replace them onto the opposite upper leg. Feet Feet Button Button L R 4 • Fold the top of the pad down. Insert the waist belts through the slots in the pad.Make sure the waist belts are not twisted. • Turn the seat upright. • Fit the pad edges around the rim of the seat. • Hook the two fastener straps on each side of the pad under the rim on each side of the seat. Slots Waist Belts Pad • Position the seat upright. • Place the pad onto the seat with the ruffle toward the top of the seat. • Fold the bottom of the pad up. Insert the crotch belt through the slot in the pad.Make sure the crotch belt is not twisted. Crotch Belt Slot Ruffle Seat • Fold the top of the pad down. • Insert the two elastic loops on the pad through the holes in the seat bottom • While holding the elastic loops in place, turn the seat face down. • Hook the elastic loop on the left side onto the peg on the right side. • Hook the elastic loop on the right side onto the peg on the left side. Bottom View Elastic Loops Elastic Loops Peg Hole Hole Hint: The elastic loops should cross over each other when attached correctly to the pegs. Assembly 5 6 5 7 8 Seat Motorized Frame Tube Hole • Press the button on the seat tube and slide the seat tube into the motorized frame tube.Make sure the button on the seat tube “snaps” into the larger hole in the motorized frame tube. Press Seat Tube Button • Insert an M4 x 31.5 mm bolt through the seat tube arm and seat tube. • Attach an M4 lock nut to the bolt.Make sure the rounded side of the lock nut faces out. • Using an adjustable wrench, hold the lock nut in place. Then using a Phillips screwdriver, tighten the bolt.Do not over-tighten. M4 Lock Nut Rounded Side M4 x 31.5 mm Bolt Shown Actual Size Assembly 6 • While pressing the button on the seat tube, slide the seat tube arm onto the seat tube.Make sure the button on the seat tube “snaps“ into the hole in the seat tube arm. 12 Press Seat Tube Button Seat Tube Arm Hole • Turn the seat upright. • Insert the tray tabs into the slots in each side of the seat. Tray Slot 11 9 10 Assembly 7 • Insert a M4 x 31.5 mm bolt through smaller hole in the motorized frame tube and into the seat tube. •Attach an M4 lock nut to the bolt. Make sure the rounded side of the lock nut faces out. •Using an adjustable wrench, hold the lock nut in place. Then, using a Phillips Screwdriver, tighten the bolt. Do not over-tighten. M4 x 31.5 mm Bolt Shown Actual Size M4 Lock Nut Rounded Side •Fit the string (below the knot) of a toy through the slot in a clip on the mobile. •Pull down on the toy to be sure it is secure on the mobile. •Repeat this procedure to assemble the other three toys to the mobile. Note: Toys may be different than those shown. Clip Slot Clip Mobile Toy Toy 14 13 Assembly 7 • Insert a M4 x 31.5 mm bolt through smaller hole in the motorized frame tube and into the seat tube. •Attach an M4 lock nut to the bolt. Make sure the rounded side of the lock n...