Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
5. Now, begin moving and follow your unit. 6. When you reach your destination, be sure to cancel your navigation: press MENU|MENU|v to CANCEL NAVIGATION|ENT. A confirmation message will appear. Press <|ENT. 49 Figure 1. Figure 2. Figure 3. Figure 4. Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 2. A trail is always converted to a route when you navigate the trail. On the Map Page, the trail you are navigating is represented by a magenta line when the visible trail option is on. The course you are following is represented by a red line. The magenta trail line overlays the red course line. To see the red course line, you much turn off the visible trail option. The Navigation Page will show only the red course line, unless you are recording a new trail. The bearing arrow on the compass rose points to the next waypoint on the trail. As you travel, the arrival alarm will go off when you near a trail way- point, and the bearing arrow on the compass rose will swing around and point to the next trail waypoint. Press EXIT to clear the alarm. 50 Magenta trail line Trail point Present position arrow North Magenta trail line Trail point Present position arrow North Navigate trail: Driver (left) is heading southeast straight toward trail point 3. Driver (right) has reached point 3 and has turned southwest to follow the trail. Track or compass heading indicator Trail waypoint symbol Bearing arrow Arrival alarm Red course line made from trail Cross track error range (off course indicator) Magenta new trail Navigate trail, navigation page (compass rose) views: Driver is heading north straight toward trail point 3 (left). Bearing arrow shows the bearing to the trail point is 355 degrees. Driver has reached trail point 3 (right), causing the Arrival alarm to go off. The unit now shows navigation information to point 4, which is 1.42 miles away. Navigate a Back Trail 1. Press MENU|MENU|v to MY TRAILS|ENT. 2. Press v to enter the Saved Trail list, then use ^ or v to select the desired Trail Name|ENT. 3. Press v> to NAVIGATE|ENT. 4. Press v> to REVERSE ROUTE|ENT|< to NAVIGATE|ENT. The unit shows navigation information along the trail, in reverse. 51 NOTE: If you are already located at or near the end of your trail, the arrival alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and allow the unit to guide you. 6. When you reach your destination, be sure to cancel your navigation. Press MENU|MENU|v to CANCEL NAVIGATION|ENT. A confirmation message will appear. Press <|ENT. Transfer Custom Maps and GPS Data Files Custom Maps: Custom maps work only from the MMC card or SD card. When a card containing a Custom Map File is loaded into the unit, the unit automatically loads the map into memory when the unit is turned on. Instructions for copying Custom Map Files to an MMC are contained in the instruction manual for your MMC card reader and MapCreate 6 software. For instructions on inserting an MMC into the unit, see Sec. 2, Installation/Accessories. GPS Data files: GPS Data Files contain waypoints, routes, trails and event marker icons. Instructions for copying GPS Data Files between your computer and an MMC are contained in the instruction manual for your MMC card reader and MapCreate 6 software. You must enter which way you want to transfer data, from an MMC card to the unit (load) or from the unit to an MMC card (save). GPS data automatically recorded in the unit's internal memory must be saved to the MMC (as a GPS Data File) in order to store it on your personal computer. GPS Data Files stored on an MMC must be copied from the card to the unit's internal memory before the unit can read them. 52 Insert the MMC into your unit. Press MENU|MENU|v to SYSTEM SETUP|ENT|v to TRANSFER MY DATA|ENT. 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the unit in order to activate the Load or Save commands. To transfer data from the unit to the MMC: press ENT (for SAVE.) To transfer data from the MMC to the unit: press > to LOAD|ENT. 3. Saving to MMC: To accept the default name "Data" for the GPS Data File, press v to SAVE DATA|ENT. If you wish to rename the file (as shown in the following figures), press ENT to activate the selection box. Press ^ or v to change the first character, then press > to the next character and repeat until the name is correct. Then, press ENT|v to SAVE DATA|ENT. The unit will display first a progress then a completion message when the data transfer is finished. To return to the Page view, repeatedly press EXIT. These figures (from left) show the menu sequence for naming and saving a GPS Data File from the unit's memory to an MMC. 4. Loading to unit memory: There may be more than one GPS Data File (*.USR) on the card. To select ...