Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Hull Suction cup Bracket Transducer Portable transducer installed on boat transom. 30 Section 2: Operation Keyboard Basics The unit sounds a tone when you press any key. Numbers in the figure correspond to key explanations below: 3 2 1 Eagle FishEasy 250 DS. 1. PWR/CLEAR In this manual, the Power/Clear key is referred to as PWR. Press this key to turn the unit on and off. It also clears menus and menu selections from the screen. To clear a menu from the screen, press PWR. NOTE: Hold the PWR key down for five seconds to turn off the unit. 31 2. MENU UP & MENU DOWN These keys appear in the manual text as MENU UP or MENU DOWN. Most of the time, you can press either of the menu keys, so in those cases, the text uses the word MENU. When the instructions say MENU, you can press the MENU UP key for consistency. The MENU UP key cycles forward through the menus. The MENU DOWN key moves backward through the menus. To scroll through the menus, repeatedly press a MENU key. 3. UP & DOWN ARROWS (^v) These Up and Down arrow keys are referred to as v (Down) or ^ (Up) in this manual. You will use these keys to adjust most features and functions on your unit. Memory This unit has permanent memory that saves the following user settings when power is turned off: Units of Measure, Temp Size, Depth Size, Fish I.D. mode, Noise Reject mode, Range mode, Zoom, Sensitivity, Grayline, Chart Speed, Battery Alarm, Display Contrast, Backlight, Language, Fish Alarm, Battery Alarm and Shallow and Deep alarms. It does not require, nor does it use an internal backup battery, so you never have to worry about replacement batteries. Menus This unit's menus will guide you through its various functions and features. Menu names and settings appear in the manual as small capital letters like SENSITIVITY, which refers to the Sensitivity menu. The MENU keys access these features, allowing you to customize unit settings. To switch menus, press MENU repeatedly. Press PWR to clear menus from the screen. 32 The Backlight menu with backlight turned on. Display The lights will flash for about 10 seconds when the unit is turned on. The backlight menu will appear on the screen. Use ^v to turn the backlight on or off. Press PWR to clear the menu from the screen. The unit will show the Full Chart Page or mode. The depth range is displayed as the upper and lower limit on the left side of the screen. In the following figure, the screen shows a depth range from 0 to 80 feet and the bottom depth is 36.9 feet, shown by the digital sonar. The water temperature is 34.5° F. 33 Digital depth Water Temp Bottom signal Depth range at bottom of depth scale Surface signal Fish symbols Structure or cover Grayline. Full Chart page. Full Chart The unit's default page, Full Chart shows all echoes scrolling across the full screen. The bottom signal scrolls across the screen from right to left. The line at the top of the screen represents the surface. The bottom depth — determined by the digital sonar — can be displayed in the upper left corner of the screen. If the transducer with a built-in temperature sensor is connected, a digital display for water temperature also will be shown. This temperature display can be turned on and off. 34 Digital depth Water Temp Bait fish Bottom signal Depth range at bottom of depth scale Surface clutter Structure or cover Fish arches Grayline. Full Chart page showing digital depth (above) and temp (below). The Fish I.D. feature is turned off. FasTrack. This feature automatically converts echoes to short horizontal lines on the display's far right side. The rest of the screen continues to operate normally. Full sonar chart showing surface clutter, a thermocline and some fish echoes. Surface Clutter Thermocline with fish echo Fish echoes 35 FasTrack gives you a rapid update of conditions directly under the boat, making it useful for ice fishing or when fishing at anchor. When the boat is not moving, fish signals are long, drawn out lines on a normal display. FasTrack converts the graph to a vertical bar graph that makes a useful addition to fishing at a stationary location. Depth Range The unit automatically adjusts the depth range according to water conditions. When in auto range mode, it always keeps the bottom displayed in the lower portion of the screen. You can override automatic depth range control and manually select a depth range. To do this, repeatedly press MENU until the DEPTH RANGE menu appears. Press v to select MANUAL, then press MENU UP to display the RANGE menu. Use the arrow keys to select a desired depth range. When you are finished, press PWR to clear the menu from the display. This unit has the following depth ranges: 0-10, 0-15, 0-20, 0-30, 0-40, 060, 0-80, 0-100, 0-150, 0-200, 0-300, 0-400, 0-600, 0-800, 0-1000, 0-1500, 0-2000 and 0-3000 feet. Depth Range menu with Manual setting selected (left). Range menu with 0-60 ft highlighted (right). 36 Zoom The zoom feature enlarges all images on the screen by doubling (2X) or quadrupl...
Эта инструкция также подходит к моделям:Эхолоты - FishEasy 250 DS (2.12 mb)