Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
The transceiver changes to the weather channel mode. 2. Press the or key to change to other weather channels. 3. To exit from the weather channels, press the WX key. The transceiver recalls the previous non-weather channel. page 10 Owner’s Manual HX350S 4.7 SCAN 1. Select the desired channel to be scanned using the or key. 2. Press the MEM key to store the channel into the transceiver's memory. “MEM” is displayed on the LCD. 3. Repeat steps 1 and 2 for all the channels to be scanned. 4. To delete a channel from the transceiver’s scan memory, press the MEM key again while the memorized channel is displayed. “MEM” disappears. 5. All channels programmed remain in the transceiver’s scan memory even if the power is turned off. See section “4.17 RESETTING THE TRANSCEIVER’S MICROPROCESSOR” to clear all the transceiver's scan memory. 6. Adjust the SQUELCH CONTROL knob until background noise is eliminated. 7. To start scan, press the SCAN key. The scan proceeds from the lowest to the highest programmed channel number and stops on channels when a transmission is received. 8. To stop the scan, press the SCAN key. 4.8 PRIORITY SCAN 1. The following channels can be set as the priority channel; 16, 09, A, and B. To set the priority channel, hold down the 16/9 key and press the MEM key. The channel changes from 16 to 09 to A to B channel with each press of the MEM key. The displayed channel is set to the priority channel. 2. For priority scanning, hold down the SCAN key at least 1 second during normal scanning, Scanning will proceed between the memorized channels and the priority channel. The priority channel will be scanned after each programmed channel. 3. For example, channels 06, 07, 08 are memorized in the transceiver’s memory, Priority scanning will proceed in the following sequence: CH06 Priority channel CH07 CH08 Priority channel Priority channel 4. Even when the transceiver stops and listens to the signal of a programmed channel, the transceiver will dual watch between this channel and the priority channel. HX350S Owner’s Manual page 11 4.9 WEATHER ALERT In the event of extreme weather disturbances such as storms and hurricanes, NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather reports on the weather channels. The transceiver is capable of receiving this alert if the following is performed: 1. Program weather channels into the transceiver’s memory for scanning. Follow the same procedure as for regular channels under Section 4.7. 2. Press the SCAN key to start the scan. 3. The memorized weather channels are scanned along with the regular memorized channels. Scan does not stop for normal weather broadcast. 4. When an alert is received on a weather channel, scanning stops and the transceiver enters the WEATHER ALERT MODE. 5. When the transceiver is in the WEATHER ALERT MODE, a loud tone is sounded. 6. Press the WX key to stop the alert tone and receive the voice information on the weather channel. 4.10 EMERGENCY CHANNEL 16 1. To select the emergency channel, press the 16/9 key from any channel. 2. Transmit your emergency signal in the same manner as on regular channels. If you can not contact anyone on channel 16, switch to another channel. 3. See the OWNER’S MANUAL SUPPLEMENT for additional emergency operating practices. 4. To recall the previous channel from 16, press the 16/9 key. 4.11 CHANNEL 9 Channel 9 is used as a hailing channel for initial, non-emergency contact with other vessels. Hold down the 16/9 key for 1 second to select channel 9. 4.12 OPERATING ON CHANNEL 13 Channel 13 is used at docks, bridges and for maneuvering in port. Messages on this channel must concern navigation only, such as meeting and passing in restricted waters. In emergencies and when approaching blind river bends, high power is allowed. Hold down the H/L key to temporarily switch to high power. High power can only be accessed in USA and Canadian modes. When the H/L key is released, the transceiver will revert low power. page 12 Owner’s Manual HX350S 4.13 OPERATING ON CHANNEL 67 When channel 67 is used for navigational bridge-to-bridge traffic between ships, high power may be used temporarily in the USA mode by pressing the H/L key. When the H/L key is released, the transceiver will revert low power. 4.14 CHANNEL A/B INSTANT ACCESS Two user-assigned channels can be programmed for instant access. USA channels 9 and 16, and WX channels should not be assigned as A or B channels because they are readily available with the 16/9 and WX keys. If the A/B key is pressed and no channel A or B has been assigned, the LCD will display “– –” and no channel number will be present. 4.14.1 Programming 1. Hold down the A/B key and then turn on the transceiver. 2. The blinking letter A will appear on the display, and dashes “– –” indicate that no channel has been designated Channel A. 3. Press the or key until the desired channel number is displayed. 4. With the desired chan...
Эта инструкция также подходит к моделям:Эхолоты - Hx 350s (102.95 kb)