|
Фрагмент инструкции
· Real Time View Off: the Weather data is not displayed. The layer displayed is the one selected into the previous menu item. 15.0.3 Type of Data Allows selecting the type of data among: Wind, Wave Data, Wheater, Humidity, Temperature, Visibility. Page 78 CP500 16. TROUBLESHOOTING The GPS Chart Plotter does not turn On. The voltage or the polarity may not be correct. Make sure that the correct voltage (10-35 volt dc) is present. Check also that the polarity is correct. The GPS Chart Plotter does not get a valid fix. The GPS WAAS Smart Antenna may not be in a open sky position or the antenna cable may not be properly connected. Make sure that no metal obstacle is placed around the antenna acting as a shield for the antenna and disconnect and connect again the antenna cable to the GPS Chart Plotter. If, after 15 minutes, the GPS Chart Plotter does not get the fix, turn it Off and On again. The GPS Chart Plotter does not turn Off. Pressing [PWR] (for at least 3 seconds) the GPS Chart Plotter does not turn Off, turn Off the voltage. Perform RAM clear. Refer to section 17.0.0 RAM Menu (reset). The GPS Chart Plotter screen becomes very dark after a long exposure to direct sunlight. The internal temperature is very high. Control the contrast. Protect the GPS Chart Plotter from direct sunlight. The GPS Chart Plotter does not respond to any command. Try to turn Off, and then turn On. If the problem persists, reset the RAM (refer to section 17.0.0 RAM Menu (reset)) or remove power from the battery. The location of my fix is not shown correctly on the Chart page. This is usually caused when C-MAP Geo-References a nautical chart. Contact C-MAP with the Latitude & Longitude of your vessels position, the position where you think your vessels should be and with details of the cartography areas, which can be seen by selecting the Chart page, press [INFO], move the ShuttlePoint knob to Data Source and press [ENT]. Write down the “Compilation scale”, “Notice to mariners” and “Horizontal datum”. Next contact C-MAP USA at 508/477-8010 and advise the problem. After storing the Chart Plotter over the winter, It takes a long time to receive a fix. This is usually caused by the internal rechargeable memory battery from becoming low which could cause the Internal RAM memory to become corrupted. To solve this issue, perform a RAM clear (refer to Section 17). NOTE After performing a RAM Clear all Marks, Routes and tracks will be erased. To back up these points refer to Section 11 for details. CP500 Page 79 Page 80CP500 17. TECHNICAL TESTS 17.0 SYSTEM TEST If you have connected your GPS Chart Plotter according to the instructions, and chosen the proper menu selection for your device, and are still having problems with your GPS Chart Plotter, the extended auto-test should help determine the problem. Make sure the GPS Chart Plotter is turned Off. While pressing and holding [CLR], turn the GPS Chart Plotter On. A new menu will appear on the display: Figure 17.0 - System Test Use the ShuttlePoint knob to select the desired test. Choose the test, press [ENT]. To exit from any submenu press [CLR]. To exit from the System Test turn Off the GPS Chart Plotter. 17.0.0 RAM Menu (reset) NOTE After performing a RAM Clear all Marks, Routes and tracks will be erased. To back up these points refer to Section 11 for details. This test verifies the integrity of the memories and if desired during this test all the internal memory can be erased and the default setting restored. RAM Clear To clear internal memory. If the GPS Chart Plotter exhibits unusual operations, or appears to be malfunctioning, it may be possible to correct the problem by clearing RAM. This operation will erase all Marks, Routes, stored Track plots and Destinations. It will also return all selections (Input Data Format, Autopilot selection, etc.) to original default values. To confirm clear RAM press [ENT] again (but if at this time you do not wish to clear RAM press [CLR]). 17.0.1 DIM Menu To select the desired value for brightness and keypad light. Contrast Each time you move the ShuttlePoint knob to right, the screen will decrease brightness, move it to the left to increase brightness. CP500 Page 81 Backlight The second option allows to set the backlight. Operates in similar mode as Contrast. 17.0.2 Cartridges (used by Standard Horizon Technicians) To check the C-CARD and its connector. Internal Data Base Test To test the WorldWideBackground. C-CARD Test To test the C-CARD. There are the possible situations: 1. if there is a C-CARD inserted in the slot and there is not a malfunction, the name of the C-CARD zone and the message "OK" are shown. 2. if there is a C-CARD inserted in the slot, but it is a defective C-CARD, the name of the C-CARD zone and the message "Faulty" are shown. 3. if there is not any C-CARD inserted in the slot, the message "not present" is shown. 4. if there is a User C-CARD inserted in the slot, the message USER C-CARD is shown. C-CARD Connector Indicates if t...
Эта инструкция также подходит к моделям:Эхолоты - CP500 (2.58 mb)