Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Each unit is both a listener and a talker to the next unit in the chain. The endcap plug sends the last talker’s broadcast back to the first listener/talker, which is usually the fish finder. Only two sentence headers are used: the standard NMEA ‘$SDDBT’ (SONAR Data Depth Below Transducer) for bottom following, and ‘$PCMAG’ (Proprietary Cannon MAG) for system control. Several features have been included in the remote interface that would allow the electromechanical system to be used for other types of applications. *Note: The CannonLink system outputs data from only one single Speed & Temp Sensor Fish. NEW FE ATURE S 4 Downrigger Mounting on Boats A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job. Due to the great variety of boats available, mounting your downrigger can be a dilemma. Having proper mounting accessories is essential. Cannon has a complete line of mounting accessories to conveniently mount your downriggers on any boat. Clamp Mounts can be mounted at the junction of two rail sections with the aid of two .” pieces of plywood. They will protect your rail from any marks from the clamp and provide a non-slip surface. Arrows Indicate Mounting Locations Deck Plate Gimbal Mount Clamp Mount Mounting Accessories Deck Plates are necessary when extra strength must be added to the base material of the boat and for attaching the downrigger to other mounting accessories. Gimbal Mounts are designed to fit mediumsized flush mounted rod holders built into the gunwale of many larger fishing boats and cruisers. Only sturdy, high quality rod holders should be used for this temporary mounting system. Gimbal mounts are available in 9” or 12” post lengths. MOUNT I NG & S E TUP 5 Side Rail Mounting Side/Rail mounts can be mounted to a welded T section. They can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces. You can also use these for mounting to a very narrow side gunwale. There is a plate provided for back-up with bolts and washers. If the gunwale compartment is foamed in, then wellnuts should be used. It is also recommended to install two additional flat head screws through the top plate for stabilization (you will need to drill and countersink). NOTE: In no case should this mount be used on fiberglass ." thick or less unless it is foamed in. Pedestal Mounting Pedestals are used wherever additional height is needed for ease of operation or to clear obstructions, such as handrails. Caution: When using a pedestal mount or side/rail mount, do not extend the telescopic boom on your Mag 20 DT. The increased leverage will cause excessive strain and possible failure of the mount. Side/Rail on T-Section Side/Rail on Gunwale Pedestal for Additional Height MOUNT I NG & S E TUP 6 NOTE: When using the telescopic boom, we strongly recommend the use of a deck plate on all boats to provide adequate stability for the downrigger. The Low-Profile Swivel Base mounting follows the same procedure as for the deck plate except that four 1/4”-20 x 2 1/2" truss head screws are used to fasten the mounting base and four additional 1/4”-20 x 2 1/2" truss head screws fix the swivel base to the boat deck. If access to the underside of the deck is not available, the deck plate can be mounted using screws and wellnuts. Drill 1/2" holes. Use four 1/4- 20 x 2" flat head screws and four wellnuts to mount deck plate as pictured. Tighten the screws so the wellnuts are firmly compressed. Where the underside is accessible, the deck plate can be mounted using screws, nuts, and washers. Drill 9/32" holes. Use four 1/4-20 x 2" flat head screws, nuts and washers (flat and lock). Fasten plate to deck as pictured. To secure the mounting base to the deckplate use four 1/4-20 x 2" truss head screws. Installing the Base on Your Boat Decks up to 7/16" thick Where access to the underside of the deck is not available, the mounting base can be mounted using wellnuts. Use the base as a template to mark locations and drill four 1/2" holes. Mount the base using four 1/4-20 x 4" truss head screws and four wellnuts. Tighten the screws so the wellnuts are firmly compressed as pictured. Decks thicker than 7/16" For decks thicker than 7/16", or where the underside of the deck is accessible, mount the base with screws, nuts, and washers. Use the base as a template to mark the locations and drill four 9/32" holes. Use four 1/4-20 x 4" truss head screws and four each flat washers, lock washers, and nuts. Fasten the base to the deck as pictured. NOTE: Wellnuts cannot be used on decks thicker than 7/16". Decks thinner than 1/4" Use a Cannon deck plate to prevent deflection and add stability to decks thinner than 1/4". Use the deck plate as a template to mark the hole locations. De...
Эта инструкция также подходит к моделям:Эхолоты - Mag 20 Dt/Hs (2.84 mb)