Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Equipment placed in the rod holders and the loss thereof is the responsibility of the user and is in no way warranted by JOHNSON OUTDOORS, INC. Mounting must be in accordance with the above instructions and diagram to be warranted. Dual Rod Holder Assembly Angled Shoulder 9 WIRING YOUR Wiring Your Downrigger Your Boat's Electrical Condition It is important to make sure that your boat is properly set up before installing your Mag 10HS \ Mag 10TS \ Mag 5HS with Positive Ion Control. Whenever a boat is in water, various submerged parts interact to create weak electrical currents. These weak electrical currents must be controlled to extend the life of the boat's metal parts and ensure a good fish catching environment. Check the zinc sacrificial anodes on your boat and on the outboard/outdrive. If they are more than 50% dissolved they should be replaced. Any coating of slime or growth should be cleaned off. All metal parts including the hull (if metal) must be interconnected by a grounding wire. This includes motor shafts, outdrives, and through hull fittings. If your boat and zincs are set up correctly, the voltage on the stainless steel spool wire of your downrigger should be positive when in contact with the water. The following tips can be useful: • Use Cannon vinyl coated lead weights. Lead, if not pure, can produce negative charges. • Use the trolling weight insulators supplied with your downrigger. This insulates your weight from the positive charge on the cable. This will also ensure that the trolling weight will stop at water level when retrieved. • The cable on your downrigger should be replaced every two years. Etching of the cable can weaken it physically and electrically. • In saltwater, make sure the sacrificial zincs are replaced when half dissolved. This ensures that the boat will run with a neutral or slightly positive charge. Clean zincs on a regular basis with a non-corrosive brush. • Always make sure the boat is properly grounded to the water. This will help ensure proper PIC voltage on the cable and that the Short Stop will function properly. Battery Fuse Holder Electrical Specifications & Wiring Instructions The Mag 10HS \ Mag 10TS \ Mag 5HS are rated at 25 amps (full load), 12 volts DC and is protected by a 30 amp manual reset circuit breaker. Be sure to measure the battery voltage of your boat. WARNING! - DO NOT RUN THIS DOWNRIGGER ON A 24 VOLT BATTERY SYSTEM. THIS WILL DAMAGE THE UNIT AND VOID YOUR WARRANTY. Connecting to the Battery: It is strongly recommended that a fuse or manual-reset circuit breaker be installed at the battery on the positive lead of the power cable or that you connect the downrigger to a battery selector switch. (See Fuse and Wire Specifications below.) Connect the positive lead (RED) to the (+) post on your battery or the downrigger will not operate. Use the new quick disconnect plug to remove the downrigger without touching the battery. Tip: Control degradation of the power cables and limit corrosion by using Cannon Ox-Not antioxidant gel on all connections. FUSE / BREAKER SPECIFICATIONS: 30 Amp, 32 Volt, waterproof, fast blow. WIRE SPECIFICATIONS: 0-15 ft. (0-5 meters) 10 gauge 15-25 ft. (5-8 meters) 8 gauge 25-30 ft. (8-9 meters) 6 gauge CAUTION: When using wire longer than that provided with your unit, follow the above chart. When running more than 30 feet from the battery, contact a qualified electrician. Battery Circuit Breaker Note: Your Mag 10HS \ Mag 10TS \ Mag 5HS must be unplugged to check the natural voltage on the stainless steel cable. 10 OPERATING YOUR DOWNRIGGER Raise Off Lower Operating Your Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. This is called drop back. Attach the fishing line firmly into the line release. Press and hold the toggle switch down to lower the weight to the desired depth as indicated on the depth meter. Place the fishing rod in the rod holder and reel up the slack so that your rod has a slight bend in it. When a fish strikes the lure, the line will separate from the release. Then you will be free to fight the fish and bring it in on your rod and reel. Lowering the Weight The Mag 10HS \ Mag 10TS \ Mag 5HS can lower the trolling weight manually or powered. Manual Descent: Fast or Slow By turning the clutch knob gently clockwise (toward the boom), you can let your trolling weight descend as fast or as slowly as you wish. Turning the knob counterclockwise (away from the boom) stops the weight. This gives you control to let it plunge rapidly or sink slowly to a predetermined trolling depth. With multiple downriggers, you could start all your weights creeping down, one at a time, and then stop them each in turn. Powered Descent: One speed fits all. Hold the toggle switch down until the weight reaches the desired depth and release. The motor will stop when switch is released or moved to the neutral position. Rais...
Эта инструкция также подходит к моделям:Эхолоты - Mag 5 Hs (2.13 mb)
Эхолоты - MAG 10HS (2.13 mb)