Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Normal Operation Start-Up Options Menu Use Normal operation for on the water operation with a transducer connected. In addition, your 300 SeriesTM Fishing System uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your 300 SeriesTM Fishing System can be used on the water. Exit Normal operation by powering your 300 SeriesTM Fishing System off. 30 Simulator Simulator Use the Simulator to learn how to use your 300 SeriesTM Fishing System before taking your boat on the water. The Simulator is a very powerful tool that simulates on the water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation. NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the Start-Up Options menu as opposed to letting the 300 SeriesTM Fishing System enter Simulator automatically (as it will if a transducer is not connected and you do nothing during power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre- configure your 300 SeriesTM Fishing System for on the water operation. Any menu changes you make will be saved for later use. A message will appear on the display periodically to remind you that you are using the Simulator. Exit the Simulator by powering your 300 SeriesTM Fishing System off. System Status Use System Status to view system connections and to conduct a unit self-test. The following screens are displayed in turn when you press the VIEW button when using System Status: • Self Test • Accessory Test • GPS Diagnostic View. Exit System Status by powering your Fishing System off. 31 Self Test Self Test displays results from the internal diagnostic self test, including unit serial number, Printed Circuit Board (PCB) serial number, software revision, total hours of operation and the input voltage. System Status Self Test Screen Accessory Test Accessory Test lists the accessories connected to the system. NOTE: The speed accessory will be detected only if the paddlewheel has moved since your 300 SeriesTM Fishing System was powered up. System Status Accessory Test Screen 32 GPS Diagnostic View GPS Diagnostic View shows a sky chart and numerical data from the GPS receiver. The sky chart shows the location of each visible GPS satellite with its satellite number and a signal strength bar. A dark grey bar indicates that the satellite is being used to determine your current position. A light gray bar indicates that the satellite is being monitored, but is not yet being used. GPS Diagnostic View Satellite Being Monitored Satellite Being Used Current Latitude and Longitude Sky Chart This view also reports the current position, local time and date, and other numeric information. The current GPS Fix Type is reported as No Fix, 2D Fix, 3D Fix, or Enhanced. An Enhanced fix has been augmented using information from WAAS, EGNOS, or MSAS. A 3D or Enhanced Fix is required for navigation. HDOP (the Horizontal Dilution of Precision) is a GPS system parameter which depends on the current satellite configuration. HDOP is used to calculate the Estimated Position Error. 33 Sonar X-PressTM Menu (Sonar views only) The Sonar X-PressTM menu provides access to the settings most frequently-used. Press the MENU key once while in any of the Sonar Views to access the Sonar X-PressTM menu. NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode. Sonar X-PressTM Menu 34 Sensitivity Sensitivity controls how much detail is shown on the display and will adjust the sensitivity of all sonar frequencies. Increasing the sensitivity shows more sonar returns from small baitfish and suspended debris in the water; however, the display may become too cluttered. When operating in very clear water or greater depths, increased sensitivity shows weaker returns that may be of interest. Decreasing the sensitivity eliminates the clutter from the display that is sometimes present in murky or muddy water. If Sensitivity is adjusted too low, the display may not show many sonar returns that could be fish. NOTE: The Sensitivity setting is a global setting and will adjust the sensitivity of all sonar frequencies, as compared to specific sensitivity adjustments (such as 83 kHz Sensitivity) that allow you to adjust the level of sensitivity for one specific beam at a time. Sensitivity at Low Sensitivity at Medium Sensitivity at High To adjust the Sensitivity: 1. Highlight Sensitivity on the Sonar X-PressTM menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Sensitivity setting. (Low = 1, High = 20, Default = 10) 35 Upper Range (Advanced: Sonar, Split Sonar, Big Digits and Circular Flasher views only) Upper Range sets the shallo...