Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
3) • Slide the switch on the epilator to the 0-charge position. (0) • Plug the charger into the epilator (©) and the electrical outlet (®). • Charge the appliance for approximately 12 hours. (The charging light will stay on even after 12 hours.) The epilator can be used for approximately 30 minutes on a single full (12 hours) charge. • When using the epilator for the first time or using it for the first time in over 6 months, please ensure that you charge the appliance for approximately 20 hours. As batteries supply electricity through chemical reaction, if left for long periods of time without being charged they become difficult to charge (inactivated) and it is necessary to charge them for approximately 20 hours in order to reactivate them. • In some cases the charging light may not come on even after a few minutes and even though the charger is plugged in securely. In such cases please continue to charge the appliance and the charging light will eventually come on. • After the appliance has been fully charged it is OK to leave the appliance plugged in. • As the charging current is con- 8 trolled, the life of the batteries does not deteriorate. There is generally a memory effect whereby the voltage will be reduced if the appliance is repeatedly charged and discharged without completely using the capacity of the batteries. If the appliance is used until no charge remains in the battery and then charged for 20 hours, this effect will disappear. • Please use the charger provided to charge the battery. • Please charge and use the appliance at a temperature of between 5~40°C (41°~104°F). • It is perfectly normal for the appliance to become slightly warm when being charged or used. • If the cord becomes damaged it is not possible to replace only the cord. Please contact your nearest dealer or Panasonic Customer Service Center. NOTE: The appliance will not charge if the switch is in any position other than 0*charge. Always check to see that the charging light is on. How to operate your epilator CAUTION: Always make sure that the epilation discs and skin protector have not become damaged, cracked or deformed. If they are, then please do not use the appliance. Failure to do so can cause damage to the skin. Wet epilation • Remove the cap. • Attach the head you wish to use. • Place a small quantity of liquid body soap on the discs. • Wet the discs. • Slide the switch to 1 or 2 position and carry out epilation. NOTE: Allow the discs to spin and foam up the soap. Always use liquid body soap when carrying out epilation. Using just cold or warm water without soap will hinder the movement of the epilator. Please see “Use foam to achieve the best results” for details. • Always wash the discs well after use to remove any residual soap. NOTE: If soap is left on the discs then a white deposit can accumulate and prevent the blades from moving smoothly. Use the supplied brush to remove any remaining hair. • After epilation slide the switch to the 0*charge position. NOTE: Remove any dirt with a dry cloth and allow the appliance to dry thoroughly. Leaving the appliance wet for long periods of time can cause malodor. Use foam to achieve the best results • Apply sufficient foam. NOTE: The foam guides the hair into the discs. If there is insufficient foam, then there is the possibility that the hair may not be removed, making it difficult to properly carry 9 out epilation. • Ensure that the foam is firm enough. NOTE: If the foam is too soft, then it will be difficult to catch the hair. Increase the volume of liquid body soap or reduce the volume of water to make the foam firmer. The foaming characteristics and the firmness of foam will vary depending on the characteristics of the body soap used. • Apply the epilator at right angles to the skin and move it slowly. NOTE: After the foam is applied it is easy to move the epilator too quickly. Take care to place the head lightly against the skin and move it slowly. Dry epilation • Remove the cap. • Attach the head you wish to use. • Slide the switch to 1 or 2 position and carry out epilation. • After completing epilation, slide the switch to the 0-charge position. If you are concerned about pain during epilation then please use the 1 position. However, bear in mind that people sense pain differently so in some cases you may feel more pain on the 1 position. The movement of the discs makes some noise but this is perfectly normal. Please do not drop the appliance or bang it against anything solid. (This can cause the skin protector or epilation discs to become damaged, cracked or deformed.) Correct usage for best epilation results • For the first use, or if not having epilated for a long time, we recommend trimming hairs before epilation. Leg and arm hair should be shortened to a length of 3 to 5 mm. • Apply epilator at right angles (90°) against your skin. For best epilation results keep in contact with the skin surface. Pressing gentl...