Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Thermostat Control Commande du thermostat 3. Handle (in back) Poignee (a l’arriere) 4. Fan Setting Reglage du radiateur 5. Hi/Low Room Select Selecteur de Puissance 6. CAUTION Indicator Light Temoin d’AVERTISSEMENT 7. Cool-Touch Housing Boitier athermane 8. Front Grille Grille de devant † Dust Filter (in back) (177774-00) Filtre a poussiere (a l’arriere) A B † Consumer replaceable Remplacable par le consommateur BCAHDEFG 1. POWER Indicator Light Temoin de Puissance 2. Thermostat Control Commande du thermostat 3. Handle (in back) Poignee (a l’arriere) 4. Fan Setting Reglage du radiateur 5. Hi/Low Room Select Selecteur de Puissance 6. CAUTION Indicator Light Temoin d’AVERTISSEMENT 7. Cool-Touch Housing Boitier athermane 8. Front Grille Grille de devant † Dust Filter (in back) (177774-00) Filtre a poussiere (a l’arriere) A B † Consumer replaceable Remplacable par le consommateur POLARIZED PLUG This appliance has a polarized plug—one blade is wider than the other. To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse it. If it still does not fit, contact an electrician. Do not attempt to defeat this safety feature by modifying the plug in any way. LINE CORD SAFETY TIPS 1. Never pull or yank on cord or the appliance. 2. To insert plug, grasp it firmly and guide it into outlet. 3. To disconnect appliance, grasp plug and remove it from outlet. 4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found, this indicates that the appliance should be serviced and the line cord replaced. 5. Never wrap the cord tightly around the appliance, as this could place undue stress on the cord where it enters the appliance and cause it to fray and break. DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY DAMAGE, OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS WORKING ENTIRELY. SPECIAL ATTENTION: The use of an extension cord is not recommended. However, if it is absolutely necessary, be sure that the cord is (1) No. 14 AWG minimum size and rated no less than 1875 watts; (2) UL Listed; (3) as short as possible (long cords can overheat, as well as trip circuit breakers); (4) not used for operating more than one appliance at a time. HOW TO USE IMPORTANT: During the first few minutes of initial use, you may notice a slight odor. This is normal and will quickly disappear. This heater is intended for use on a flat, stable surface, such as a floor, tabletop, shelf, or desk in a location where the airflow grille openings won’t be obstructed. Keep all combustible materials such as furniture, pillows, bedding, paper, clothes and curtains at least 3 feet (.9 m) away from the heater. Do not use in wet or moist locations, like bathrooms or laundry areas, or in areas where paint or other flammable or volatile liquids are used or stored. CAUTION: Be sure no other appliances are plugged into the same circuit with this heater/fan. A circuit overload could occur. 1. Be sure the Dial is in the OFF position before plugging the unit in (A). Plug into an AC outlet. Turn the Room Select Dial to the appropriate setting using High for large rooms and Low for smaller area. The POWER indicator will light up. 2. Turn the Thermostat Control toward the highest level (HOT) to start in order to activate the heater/fan. Once the desired room temperature is achieved, lower the Thermostat Control back down until the fan cycles off. The heat will now cycle On/Off to maintain a comfortable level. 3. To use as a fan without heat, turn the Dial to FAN and the Thermostat Control toward the highest level (HOT) until the fan begins to operate. No heating will occur in this mode. SPECIAL FEATURES 1. This unit is equipped with a Safety Auto-Off, plus a Thermal Fuse and CAUTION light. If the unit experiences excessive heat, the Safety Auto-Off will shut the unit off, and the CAUTION light will go on. If this happens, turn the Dial to Off immediately. Be sure the grille is not blocked and nothing is restricting airflow. If the CAUTION light stays on, unplug the unit, let it cool down, and wait 10 minutes before plugging it back in to operate. Readjust your temperature or room settings. If the unit fails to operate after 10 minutes, it may mean the heater has internal damage and that the Thermal Fuse has been tripped so the heater can no longer operate. 2. The POWER Indicator Light shows that the heater is switched on and operating. It continues to glow even if the thermostat has cycled and the heating elements are off. Note that even though this unit has a Cool-Touch Housing, the front grille will get hot. Be careful not to touch it. CARE AND CLEANING This appliance is permanently lubricated and will not require additional lubrication for the life of the unit. It contains no user serviceable parts. Refer service to qualified service personnel. 1. Always turn the unit OFF, unplug, disconnect the cord from the outlet, and allow the heater to cool compl...